How do I take off these plastic buttons that are attaching the shroud to my car?
I need to get a closer look at my headlight assembly, but there is a plastic shroud/guard covering it. It's attached with little plastic buttons.
plastic clips
New contributor
add a comment |
I need to get a closer look at my headlight assembly, but there is a plastic shroud/guard covering it. It's attached with little plastic buttons.
plastic clips
New contributor
Do I just squeeze the bottom with pliers and pull it out?
– raimond
yesterday
add a comment |
I need to get a closer look at my headlight assembly, but there is a plastic shroud/guard covering it. It's attached with little plastic buttons.
plastic clips
New contributor
I need to get a closer look at my headlight assembly, but there is a plastic shroud/guard covering it. It's attached with little plastic buttons.
plastic clips
plastic clips
New contributor
New contributor
edited yesterday
Pᴀᴜʟsᴛᴇʀ2♦
109k16167360
109k16167360
New contributor
asked yesterday
raimondraimond
435
435
New contributor
New contributor
Do I just squeeze the bottom with pliers and pull it out?
– raimond
yesterday
add a comment |
Do I just squeeze the bottom with pliers and pull it out?
– raimond
yesterday
Do I just squeeze the bottom with pliers and pull it out?
– raimond
yesterday
Do I just squeeze the bottom with pliers and pull it out?
– raimond
yesterday
add a comment |
1 Answer
1
active
oldest
votes
Put a screwdriver in the slot on the side and gently raise up the center section. You may need to work it from both sides. Once the center section is raised, it should look something like this:
Once the center section is raised, grab it from the base (or put your screwdriver under the base) and wiggle it free.
3
In addition to using a flathead screwdriver, there are various styles of trim removal tools available that I've found to be gentler with the sometimes brittle plastic. My preferred style for these types of clips is a tool like this.
– Alexander
22 hours ago
4
And whenever you need to remove those kinds of clips, know that some of the clips will break. They're just not made for re-use but for quick and easy installation (in the factory). You may want to get a bunch of them as replacements, either cheap generic ones from a set or the one or two types you expect to encounter from the dealership. If you have like 10 spares of each ready, you may find the repair to go much easier because you don't worry and spend 10 minutes to remove a single clip without breaking it, or worse, damage the part held by the clip while trying to keep the clip intact.
– JimmyB
14 hours ago
add a comment |
Your Answer
StackExchange.ready(function() {
var channelOptions = {
tags: "".split(" "),
id: "224"
};
initTagRenderer("".split(" "), "".split(" "), channelOptions);
StackExchange.using("externalEditor", function() {
// Have to fire editor after snippets, if snippets enabled
if (StackExchange.settings.snippets.snippetsEnabled) {
StackExchange.using("snippets", function() {
createEditor();
});
}
else {
createEditor();
}
});
function createEditor() {
StackExchange.prepareEditor({
heartbeatType: 'answer',
autoActivateHeartbeat: false,
convertImagesToLinks: false,
noModals: true,
showLowRepImageUploadWarning: true,
reputationToPostImages: null,
bindNavPrevention: true,
postfix: "",
imageUploader: {
brandingHtml: "Powered by u003ca class="icon-imgur-white" href="https://imgur.com/"u003eu003c/au003e",
contentPolicyHtml: "User contributions licensed under u003ca href="https://creativecommons.org/licenses/by-sa/3.0/"u003ecc by-sa 3.0 with attribution requiredu003c/au003e u003ca href="https://stackoverflow.com/legal/content-policy"u003e(content policy)u003c/au003e",
allowUrls: true
},
noCode: true, onDemand: true,
discardSelector: ".discard-answer"
,immediatelyShowMarkdownHelp:true
});
}
});
raimond is a new contributor. Be nice, and check out our Code of Conduct.
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function () {
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2fmechanics.stackexchange.com%2fquestions%2f62517%2fhow-do-i-take-off-these-plastic-buttons-that-are-attaching-the-shroud-to-my-car%23new-answer', 'question_page');
}
);
Post as a guest
Required, but never shown
1 Answer
1
active
oldest
votes
1 Answer
1
active
oldest
votes
active
oldest
votes
active
oldest
votes
Put a screwdriver in the slot on the side and gently raise up the center section. You may need to work it from both sides. Once the center section is raised, it should look something like this:
Once the center section is raised, grab it from the base (or put your screwdriver under the base) and wiggle it free.
3
In addition to using a flathead screwdriver, there are various styles of trim removal tools available that I've found to be gentler with the sometimes brittle plastic. My preferred style for these types of clips is a tool like this.
– Alexander
22 hours ago
4
And whenever you need to remove those kinds of clips, know that some of the clips will break. They're just not made for re-use but for quick and easy installation (in the factory). You may want to get a bunch of them as replacements, either cheap generic ones from a set or the one or two types you expect to encounter from the dealership. If you have like 10 spares of each ready, you may find the repair to go much easier because you don't worry and spend 10 minutes to remove a single clip without breaking it, or worse, damage the part held by the clip while trying to keep the clip intact.
– JimmyB
14 hours ago
add a comment |
Put a screwdriver in the slot on the side and gently raise up the center section. You may need to work it from both sides. Once the center section is raised, it should look something like this:
Once the center section is raised, grab it from the base (or put your screwdriver under the base) and wiggle it free.
3
In addition to using a flathead screwdriver, there are various styles of trim removal tools available that I've found to be gentler with the sometimes brittle plastic. My preferred style for these types of clips is a tool like this.
– Alexander
22 hours ago
4
And whenever you need to remove those kinds of clips, know that some of the clips will break. They're just not made for re-use but for quick and easy installation (in the factory). You may want to get a bunch of them as replacements, either cheap generic ones from a set or the one or two types you expect to encounter from the dealership. If you have like 10 spares of each ready, you may find the repair to go much easier because you don't worry and spend 10 minutes to remove a single clip without breaking it, or worse, damage the part held by the clip while trying to keep the clip intact.
– JimmyB
14 hours ago
add a comment |
Put a screwdriver in the slot on the side and gently raise up the center section. You may need to work it from both sides. Once the center section is raised, it should look something like this:
Once the center section is raised, grab it from the base (or put your screwdriver under the base) and wiggle it free.
Put a screwdriver in the slot on the side and gently raise up the center section. You may need to work it from both sides. Once the center section is raised, it should look something like this:
Once the center section is raised, grab it from the base (or put your screwdriver under the base) and wiggle it free.
answered yesterday
Pᴀᴜʟsᴛᴇʀ2♦Pᴀᴜʟsᴛᴇʀ2
109k16167360
109k16167360
3
In addition to using a flathead screwdriver, there are various styles of trim removal tools available that I've found to be gentler with the sometimes brittle plastic. My preferred style for these types of clips is a tool like this.
– Alexander
22 hours ago
4
And whenever you need to remove those kinds of clips, know that some of the clips will break. They're just not made for re-use but for quick and easy installation (in the factory). You may want to get a bunch of them as replacements, either cheap generic ones from a set or the one or two types you expect to encounter from the dealership. If you have like 10 spares of each ready, you may find the repair to go much easier because you don't worry and spend 10 minutes to remove a single clip without breaking it, or worse, damage the part held by the clip while trying to keep the clip intact.
– JimmyB
14 hours ago
add a comment |
3
In addition to using a flathead screwdriver, there are various styles of trim removal tools available that I've found to be gentler with the sometimes brittle plastic. My preferred style for these types of clips is a tool like this.
– Alexander
22 hours ago
4
And whenever you need to remove those kinds of clips, know that some of the clips will break. They're just not made for re-use but for quick and easy installation (in the factory). You may want to get a bunch of them as replacements, either cheap generic ones from a set or the one or two types you expect to encounter from the dealership. If you have like 10 spares of each ready, you may find the repair to go much easier because you don't worry and spend 10 minutes to remove a single clip without breaking it, or worse, damage the part held by the clip while trying to keep the clip intact.
– JimmyB
14 hours ago
3
3
In addition to using a flathead screwdriver, there are various styles of trim removal tools available that I've found to be gentler with the sometimes brittle plastic. My preferred style for these types of clips is a tool like this.
– Alexander
22 hours ago
In addition to using a flathead screwdriver, there are various styles of trim removal tools available that I've found to be gentler with the sometimes brittle plastic. My preferred style for these types of clips is a tool like this.
– Alexander
22 hours ago
4
4
And whenever you need to remove those kinds of clips, know that some of the clips will break. They're just not made for re-use but for quick and easy installation (in the factory). You may want to get a bunch of them as replacements, either cheap generic ones from a set or the one or two types you expect to encounter from the dealership. If you have like 10 spares of each ready, you may find the repair to go much easier because you don't worry and spend 10 minutes to remove a single clip without breaking it, or worse, damage the part held by the clip while trying to keep the clip intact.
– JimmyB
14 hours ago
And whenever you need to remove those kinds of clips, know that some of the clips will break. They're just not made for re-use but for quick and easy installation (in the factory). You may want to get a bunch of them as replacements, either cheap generic ones from a set or the one or two types you expect to encounter from the dealership. If you have like 10 spares of each ready, you may find the repair to go much easier because you don't worry and spend 10 minutes to remove a single clip without breaking it, or worse, damage the part held by the clip while trying to keep the clip intact.
– JimmyB
14 hours ago
add a comment |
raimond is a new contributor. Be nice, and check out our Code of Conduct.
raimond is a new contributor. Be nice, and check out our Code of Conduct.
raimond is a new contributor. Be nice, and check out our Code of Conduct.
raimond is a new contributor. Be nice, and check out our Code of Conduct.
Thanks for contributing an answer to Motor Vehicle Maintenance & Repair Stack Exchange!
- Please be sure to answer the question. Provide details and share your research!
But avoid …
- Asking for help, clarification, or responding to other answers.
- Making statements based on opinion; back them up with references or personal experience.
To learn more, see our tips on writing great answers.
Some of your past answers have not been well-received, and you're in danger of being blocked from answering.
Please pay close attention to the following guidance:
- Please be sure to answer the question. Provide details and share your research!
But avoid …
- Asking for help, clarification, or responding to other answers.
- Making statements based on opinion; back them up with references or personal experience.
To learn more, see our tips on writing great answers.
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function () {
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2fmechanics.stackexchange.com%2fquestions%2f62517%2fhow-do-i-take-off-these-plastic-buttons-that-are-attaching-the-shroud-to-my-car%23new-answer', 'question_page');
}
);
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Do I just squeeze the bottom with pliers and pull it out?
– raimond
yesterday