Trunk between SG200's doesn't seem to send tagged traffic (n00b)
I have a cisco SG200-26FP (switch A) connected to a cisco SG200-26P (switch B). I would like to use the existing link between both switches as a trunk so 2 VLANs can use this connection, but I'm running into some difficulties. As an extra hurdle, these devices don't allow connections via CLI, so it's only GUI I'm afraid...
Config switch A:
GE13: connection to switch B: Trunk: VLAN10 Untagged, VLAN50 Tagged
GE14: Access: VLAN50 Untagged
GE22: connection to router: General: VLAN10 Untagged, VLAN50 Tagged, VLAN51 Tagged
Config switch B:
GE20: Access: VLAN50 Untagged
GE26: connection to switch A: Trunk: VLAN10 Untagged, VLAN50 Tagged
Here's what I don't understand: on switch A, I can hang a device on port GE14 and it will receive an IP from the DHCP server on VLAN50, it will see the gateway, etc. However, on switch B, port GE20 doesn't receive an IP from the DHCP server. I can't see why and I feel I'm missing something obvious here.
Both switches hold at least one more VLAN (seperately), all is well there. There are also no issues with VLAN10.
If you need anymore info or screenshots, let me know.
networking switch vlan
add a comment |
I have a cisco SG200-26FP (switch A) connected to a cisco SG200-26P (switch B). I would like to use the existing link between both switches as a trunk so 2 VLANs can use this connection, but I'm running into some difficulties. As an extra hurdle, these devices don't allow connections via CLI, so it's only GUI I'm afraid...
Config switch A:
GE13: connection to switch B: Trunk: VLAN10 Untagged, VLAN50 Tagged
GE14: Access: VLAN50 Untagged
GE22: connection to router: General: VLAN10 Untagged, VLAN50 Tagged, VLAN51 Tagged
Config switch B:
GE20: Access: VLAN50 Untagged
GE26: connection to switch A: Trunk: VLAN10 Untagged, VLAN50 Tagged
Here's what I don't understand: on switch A, I can hang a device on port GE14 and it will receive an IP from the DHCP server on VLAN50, it will see the gateway, etc. However, on switch B, port GE20 doesn't receive an IP from the DHCP server. I can't see why and I feel I'm missing something obvious here.
Both switches hold at least one more VLAN (seperately), all is well there. There are also no issues with VLAN10.
If you need anymore info or screenshots, let me know.
networking switch vlan
As far as I am aware, there is a console port for configuration on each of these switches. Use the console port for your CLI.
– var firstName
Jan 14 at 17:55
add a comment |
I have a cisco SG200-26FP (switch A) connected to a cisco SG200-26P (switch B). I would like to use the existing link between both switches as a trunk so 2 VLANs can use this connection, but I'm running into some difficulties. As an extra hurdle, these devices don't allow connections via CLI, so it's only GUI I'm afraid...
Config switch A:
GE13: connection to switch B: Trunk: VLAN10 Untagged, VLAN50 Tagged
GE14: Access: VLAN50 Untagged
GE22: connection to router: General: VLAN10 Untagged, VLAN50 Tagged, VLAN51 Tagged
Config switch B:
GE20: Access: VLAN50 Untagged
GE26: connection to switch A: Trunk: VLAN10 Untagged, VLAN50 Tagged
Here's what I don't understand: on switch A, I can hang a device on port GE14 and it will receive an IP from the DHCP server on VLAN50, it will see the gateway, etc. However, on switch B, port GE20 doesn't receive an IP from the DHCP server. I can't see why and I feel I'm missing something obvious here.
Both switches hold at least one more VLAN (seperately), all is well there. There are also no issues with VLAN10.
If you need anymore info or screenshots, let me know.
networking switch vlan
I have a cisco SG200-26FP (switch A) connected to a cisco SG200-26P (switch B). I would like to use the existing link between both switches as a trunk so 2 VLANs can use this connection, but I'm running into some difficulties. As an extra hurdle, these devices don't allow connections via CLI, so it's only GUI I'm afraid...
Config switch A:
GE13: connection to switch B: Trunk: VLAN10 Untagged, VLAN50 Tagged
GE14: Access: VLAN50 Untagged
GE22: connection to router: General: VLAN10 Untagged, VLAN50 Tagged, VLAN51 Tagged
Config switch B:
GE20: Access: VLAN50 Untagged
GE26: connection to switch A: Trunk: VLAN10 Untagged, VLAN50 Tagged
Here's what I don't understand: on switch A, I can hang a device on port GE14 and it will receive an IP from the DHCP server on VLAN50, it will see the gateway, etc. However, on switch B, port GE20 doesn't receive an IP from the DHCP server. I can't see why and I feel I'm missing something obvious here.
Both switches hold at least one more VLAN (seperately), all is well there. There are also no issues with VLAN10.
If you need anymore info or screenshots, let me know.
networking switch vlan
networking switch vlan
edited Jan 14 at 14:42
Ahmed Ashour
1,1901614
1,1901614
asked Jan 14 at 13:01
FrankFrank
1
1
As far as I am aware, there is a console port for configuration on each of these switches. Use the console port for your CLI.
– var firstName
Jan 14 at 17:55
add a comment |
As far as I am aware, there is a console port for configuration on each of these switches. Use the console port for your CLI.
– var firstName
Jan 14 at 17:55
As far as I am aware, there is a console port for configuration on each of these switches. Use the console port for your CLI.
– var firstName
Jan 14 at 17:55
As far as I am aware, there is a console port for configuration on each of these switches. Use the console port for your CLI.
– var firstName
Jan 14 at 17:55
add a comment |
0
active
oldest
votes
Your Answer
StackExchange.ready(function() {
var channelOptions = {
tags: "".split(" "),
id: "3"
};
initTagRenderer("".split(" "), "".split(" "), channelOptions);
StackExchange.using("externalEditor", function() {
// Have to fire editor after snippets, if snippets enabled
if (StackExchange.settings.snippets.snippetsEnabled) {
StackExchange.using("snippets", function() {
createEditor();
});
}
else {
createEditor();
}
});
function createEditor() {
StackExchange.prepareEditor({
heartbeatType: 'answer',
autoActivateHeartbeat: false,
convertImagesToLinks: true,
noModals: true,
showLowRepImageUploadWarning: true,
reputationToPostImages: 10,
bindNavPrevention: true,
postfix: "",
imageUploader: {
brandingHtml: "Powered by u003ca class="icon-imgur-white" href="https://imgur.com/"u003eu003c/au003e",
contentPolicyHtml: "User contributions licensed under u003ca href="https://creativecommons.org/licenses/by-sa/3.0/"u003ecc by-sa 3.0 with attribution requiredu003c/au003e u003ca href="https://stackoverflow.com/legal/content-policy"u003e(content policy)u003c/au003e",
allowUrls: true
},
onDemand: true,
discardSelector: ".discard-answer"
,immediatelyShowMarkdownHelp:true
});
}
});
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function () {
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2fsuperuser.com%2fquestions%2f1394115%2ftrunk-between-sg200s-doesnt-seem-to-send-tagged-traffic-n00b%23new-answer', 'question_page');
}
);
Post as a guest
Required, but never shown
0
active
oldest
votes
0
active
oldest
votes
active
oldest
votes
active
oldest
votes
Thanks for contributing an answer to Super User!
- Please be sure to answer the question. Provide details and share your research!
But avoid …
- Asking for help, clarification, or responding to other answers.
- Making statements based on opinion; back them up with references or personal experience.
To learn more, see our tips on writing great answers.
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function () {
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2fsuperuser.com%2fquestions%2f1394115%2ftrunk-between-sg200s-doesnt-seem-to-send-tagged-traffic-n00b%23new-answer', 'question_page');
}
);
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
As far as I am aware, there is a console port for configuration on each of these switches. Use the console port for your CLI.
– var firstName
Jan 14 at 17:55