CPU Permanent throttles after 5 minutes of gaming, util restart












-1















I'm currently running Ubuntu Budgie, on my Asus Zenbook UX550ve, but i also had this issue on my previous OS, PopOS!.



Basically after 10 minutes of gaming, my computer starts to perform really poor. You would think it was a throttle issue due to heat, but quitting the game doesn't improve performance. (And looking at the temps doesn't seem alarming)



This is cpupower frequency-info before gaming,



  driver: intel_pstate
CPUs which run at the same hardware frequency: 0
CPUs which need to have their frequency coordinated by software: 0
maximum transition latency: Cannot determine or is not supported.
hardware limits: 800 MHz - 3.80 GHz
available cpufreq governors: performance powersave
current policy: frequency should be within 800 MHz and 3.80 GHz.
The governor "powersave" may decide which speed to use
within this range.
current CPU frequency: Unable to call hardware
current CPU frequency: 2.26 GHz (asserted by call to kernel)
boost state support:
Supported: yes
Active: yes


And this is after



analyzing CPU 0:
driver: intel_pstate
CPUs which run at the same hardware frequency: 0
CPUs which need to have their frequency coordinated by software: 0
maximum transition latency: Cannot determine or is not supported.
hardware limits: 800 MHz - 3.80 GHz
available cpufreq governors: performance powersave
current policy: frequency should be within 800 MHz and 3.80 GHz.
The governor "performance" may decide which speed to use
within this range.
current CPU frequency: Unable to call hardware
current CPU frequency: 266 MHz (asserted by call to kernel)
boost state support:
Supported: yes
Active: yes


Its current frequency will range from 200 to 800. Only a restart brings back normal levels.



I've have tried the following



Updating my bios.



Update to latest graphics driver (1050TI).



Pulling the battery from the motherboard for 2 minutes.



Force performance mode with sudo cpupower frequency-set --governor performance



But neither works. It's incredible frustrating, and i'm all out of ideas. :/










share|improve this question























  • Could be overheating. Check the temps with the sensors command. ...and by the way, "looking at the temps doesn't seem alarming" is as vague as it gets.

    – mikewhatever
    Feb 16 at 16:18













  • @mikewhatever Currently running with 298 MHz, temps are around 50c. I don't think it's due to overheating, probably something with pstate

    – MartinElvar
    Feb 16 at 16:46











  • Reported CPU frequencies below the minimum mean that there is throttling, probably Clock Modulation. The recommended tool for monitoring this stuff (for modern Intel Processors) is turbostat, included in the linux-tools-common package. I would run sudo turbostat --Summary --quiet --show Busy%,Bzy_MHz,PkgTmp,PkgWatt,IRQ --interval 15 always in a terminal. Also try without --quiet to see a big spew of stuff that should reveal if a thermal trigger has fired.

    – Doug Smythies
    Feb 16 at 17:29
















-1















I'm currently running Ubuntu Budgie, on my Asus Zenbook UX550ve, but i also had this issue on my previous OS, PopOS!.



Basically after 10 minutes of gaming, my computer starts to perform really poor. You would think it was a throttle issue due to heat, but quitting the game doesn't improve performance. (And looking at the temps doesn't seem alarming)



This is cpupower frequency-info before gaming,



  driver: intel_pstate
CPUs which run at the same hardware frequency: 0
CPUs which need to have their frequency coordinated by software: 0
maximum transition latency: Cannot determine or is not supported.
hardware limits: 800 MHz - 3.80 GHz
available cpufreq governors: performance powersave
current policy: frequency should be within 800 MHz and 3.80 GHz.
The governor "powersave" may decide which speed to use
within this range.
current CPU frequency: Unable to call hardware
current CPU frequency: 2.26 GHz (asserted by call to kernel)
boost state support:
Supported: yes
Active: yes


And this is after



analyzing CPU 0:
driver: intel_pstate
CPUs which run at the same hardware frequency: 0
CPUs which need to have their frequency coordinated by software: 0
maximum transition latency: Cannot determine or is not supported.
hardware limits: 800 MHz - 3.80 GHz
available cpufreq governors: performance powersave
current policy: frequency should be within 800 MHz and 3.80 GHz.
The governor "performance" may decide which speed to use
within this range.
current CPU frequency: Unable to call hardware
current CPU frequency: 266 MHz (asserted by call to kernel)
boost state support:
Supported: yes
Active: yes


Its current frequency will range from 200 to 800. Only a restart brings back normal levels.



I've have tried the following



Updating my bios.



Update to latest graphics driver (1050TI).



Pulling the battery from the motherboard for 2 minutes.



Force performance mode with sudo cpupower frequency-set --governor performance



But neither works. It's incredible frustrating, and i'm all out of ideas. :/










share|improve this question























  • Could be overheating. Check the temps with the sensors command. ...and by the way, "looking at the temps doesn't seem alarming" is as vague as it gets.

    – mikewhatever
    Feb 16 at 16:18













  • @mikewhatever Currently running with 298 MHz, temps are around 50c. I don't think it's due to overheating, probably something with pstate

    – MartinElvar
    Feb 16 at 16:46











  • Reported CPU frequencies below the minimum mean that there is throttling, probably Clock Modulation. The recommended tool for monitoring this stuff (for modern Intel Processors) is turbostat, included in the linux-tools-common package. I would run sudo turbostat --Summary --quiet --show Busy%,Bzy_MHz,PkgTmp,PkgWatt,IRQ --interval 15 always in a terminal. Also try without --quiet to see a big spew of stuff that should reveal if a thermal trigger has fired.

    – Doug Smythies
    Feb 16 at 17:29














-1












-1








-1








I'm currently running Ubuntu Budgie, on my Asus Zenbook UX550ve, but i also had this issue on my previous OS, PopOS!.



Basically after 10 minutes of gaming, my computer starts to perform really poor. You would think it was a throttle issue due to heat, but quitting the game doesn't improve performance. (And looking at the temps doesn't seem alarming)



This is cpupower frequency-info before gaming,



  driver: intel_pstate
CPUs which run at the same hardware frequency: 0
CPUs which need to have their frequency coordinated by software: 0
maximum transition latency: Cannot determine or is not supported.
hardware limits: 800 MHz - 3.80 GHz
available cpufreq governors: performance powersave
current policy: frequency should be within 800 MHz and 3.80 GHz.
The governor "powersave" may decide which speed to use
within this range.
current CPU frequency: Unable to call hardware
current CPU frequency: 2.26 GHz (asserted by call to kernel)
boost state support:
Supported: yes
Active: yes


And this is after



analyzing CPU 0:
driver: intel_pstate
CPUs which run at the same hardware frequency: 0
CPUs which need to have their frequency coordinated by software: 0
maximum transition latency: Cannot determine or is not supported.
hardware limits: 800 MHz - 3.80 GHz
available cpufreq governors: performance powersave
current policy: frequency should be within 800 MHz and 3.80 GHz.
The governor "performance" may decide which speed to use
within this range.
current CPU frequency: Unable to call hardware
current CPU frequency: 266 MHz (asserted by call to kernel)
boost state support:
Supported: yes
Active: yes


Its current frequency will range from 200 to 800. Only a restart brings back normal levels.



I've have tried the following



Updating my bios.



Update to latest graphics driver (1050TI).



Pulling the battery from the motherboard for 2 minutes.



Force performance mode with sudo cpupower frequency-set --governor performance



But neither works. It's incredible frustrating, and i'm all out of ideas. :/










share|improve this question














I'm currently running Ubuntu Budgie, on my Asus Zenbook UX550ve, but i also had this issue on my previous OS, PopOS!.



Basically after 10 minutes of gaming, my computer starts to perform really poor. You would think it was a throttle issue due to heat, but quitting the game doesn't improve performance. (And looking at the temps doesn't seem alarming)



This is cpupower frequency-info before gaming,



  driver: intel_pstate
CPUs which run at the same hardware frequency: 0
CPUs which need to have their frequency coordinated by software: 0
maximum transition latency: Cannot determine or is not supported.
hardware limits: 800 MHz - 3.80 GHz
available cpufreq governors: performance powersave
current policy: frequency should be within 800 MHz and 3.80 GHz.
The governor "powersave" may decide which speed to use
within this range.
current CPU frequency: Unable to call hardware
current CPU frequency: 2.26 GHz (asserted by call to kernel)
boost state support:
Supported: yes
Active: yes


And this is after



analyzing CPU 0:
driver: intel_pstate
CPUs which run at the same hardware frequency: 0
CPUs which need to have their frequency coordinated by software: 0
maximum transition latency: Cannot determine or is not supported.
hardware limits: 800 MHz - 3.80 GHz
available cpufreq governors: performance powersave
current policy: frequency should be within 800 MHz and 3.80 GHz.
The governor "performance" may decide which speed to use
within this range.
current CPU frequency: Unable to call hardware
current CPU frequency: 266 MHz (asserted by call to kernel)
boost state support:
Supported: yes
Active: yes


Its current frequency will range from 200 to 800. Only a restart brings back normal levels.



I've have tried the following



Updating my bios.



Update to latest graphics driver (1050TI).



Pulling the battery from the motherboard for 2 minutes.



Force performance mode with sudo cpupower frequency-set --governor performance



But neither works. It's incredible frustrating, and i'm all out of ideas. :/







drivers nvidia games performance cpu






share|improve this question













share|improve this question











share|improve this question




share|improve this question










asked Feb 16 at 16:03









MartinElvarMartinElvar

992




992













  • Could be overheating. Check the temps with the sensors command. ...and by the way, "looking at the temps doesn't seem alarming" is as vague as it gets.

    – mikewhatever
    Feb 16 at 16:18













  • @mikewhatever Currently running with 298 MHz, temps are around 50c. I don't think it's due to overheating, probably something with pstate

    – MartinElvar
    Feb 16 at 16:46











  • Reported CPU frequencies below the minimum mean that there is throttling, probably Clock Modulation. The recommended tool for monitoring this stuff (for modern Intel Processors) is turbostat, included in the linux-tools-common package. I would run sudo turbostat --Summary --quiet --show Busy%,Bzy_MHz,PkgTmp,PkgWatt,IRQ --interval 15 always in a terminal. Also try without --quiet to see a big spew of stuff that should reveal if a thermal trigger has fired.

    – Doug Smythies
    Feb 16 at 17:29



















  • Could be overheating. Check the temps with the sensors command. ...and by the way, "looking at the temps doesn't seem alarming" is as vague as it gets.

    – mikewhatever
    Feb 16 at 16:18













  • @mikewhatever Currently running with 298 MHz, temps are around 50c. I don't think it's due to overheating, probably something with pstate

    – MartinElvar
    Feb 16 at 16:46











  • Reported CPU frequencies below the minimum mean that there is throttling, probably Clock Modulation. The recommended tool for monitoring this stuff (for modern Intel Processors) is turbostat, included in the linux-tools-common package. I would run sudo turbostat --Summary --quiet --show Busy%,Bzy_MHz,PkgTmp,PkgWatt,IRQ --interval 15 always in a terminal. Also try without --quiet to see a big spew of stuff that should reveal if a thermal trigger has fired.

    – Doug Smythies
    Feb 16 at 17:29

















Could be overheating. Check the temps with the sensors command. ...and by the way, "looking at the temps doesn't seem alarming" is as vague as it gets.

– mikewhatever
Feb 16 at 16:18







Could be overheating. Check the temps with the sensors command. ...and by the way, "looking at the temps doesn't seem alarming" is as vague as it gets.

– mikewhatever
Feb 16 at 16:18















@mikewhatever Currently running with 298 MHz, temps are around 50c. I don't think it's due to overheating, probably something with pstate

– MartinElvar
Feb 16 at 16:46





@mikewhatever Currently running with 298 MHz, temps are around 50c. I don't think it's due to overheating, probably something with pstate

– MartinElvar
Feb 16 at 16:46













Reported CPU frequencies below the minimum mean that there is throttling, probably Clock Modulation. The recommended tool for monitoring this stuff (for modern Intel Processors) is turbostat, included in the linux-tools-common package. I would run sudo turbostat --Summary --quiet --show Busy%,Bzy_MHz,PkgTmp,PkgWatt,IRQ --interval 15 always in a terminal. Also try without --quiet to see a big spew of stuff that should reveal if a thermal trigger has fired.

– Doug Smythies
Feb 16 at 17:29





Reported CPU frequencies below the minimum mean that there is throttling, probably Clock Modulation. The recommended tool for monitoring this stuff (for modern Intel Processors) is turbostat, included in the linux-tools-common package. I would run sudo turbostat --Summary --quiet --show Busy%,Bzy_MHz,PkgTmp,PkgWatt,IRQ --interval 15 always in a terminal. Also try without --quiet to see a big spew of stuff that should reveal if a thermal trigger has fired.

– Doug Smythies
Feb 16 at 17:29










1 Answer
1






active

oldest

votes


















0














Your computer may have some minimal tools in BIOS to prevent overheat damage - and the processor being hot may not translate to "my computer feels hot to the touch"



I use a set of utilities to manage power and thermal (potential) problem in my laptop. First, install power management tools, and a program to limit CPU speed in severe cases



sudo apt install tlp thermald


Tlp has many customizable settings in /etc/default/tlp



Secondly, install programs to show me the internal temperatures of my computer:



sudo apt install --install-suggests lm-sensors psensor
sudo sensors-detect


just follow the prompts. Add the recommended lines to /etc/modules.



Now, if you don't want to reboot, you'll have to manually activate the modules.



sudo modprobe module1 module2


where module1 etc. = the module names provided from sensors-detect.



You may also need to add utilities to control the fan in your laptop



sudo apt install fancontrol
sudo pwmconfig


and work your way through the instructions there.



Finally, run sensors -s to make your fan configuration take effect.



sudo sensors -s


Now, you can check your temps.



sensors


Now to run fan control, type:



sudo /usr/sbin/fancontrol &





share|improve this answer























    Your Answer








    StackExchange.ready(function() {
    var channelOptions = {
    tags: "".split(" "),
    id: "89"
    };
    initTagRenderer("".split(" "), "".split(" "), channelOptions);

    StackExchange.using("externalEditor", function() {
    // Have to fire editor after snippets, if snippets enabled
    if (StackExchange.settings.snippets.snippetsEnabled) {
    StackExchange.using("snippets", function() {
    createEditor();
    });
    }
    else {
    createEditor();
    }
    });

    function createEditor() {
    StackExchange.prepareEditor({
    heartbeatType: 'answer',
    autoActivateHeartbeat: false,
    convertImagesToLinks: true,
    noModals: true,
    showLowRepImageUploadWarning: true,
    reputationToPostImages: 10,
    bindNavPrevention: true,
    postfix: "",
    imageUploader: {
    brandingHtml: "Powered by u003ca class="icon-imgur-white" href="https://imgur.com/"u003eu003c/au003e",
    contentPolicyHtml: "User contributions licensed under u003ca href="https://creativecommons.org/licenses/by-sa/3.0/"u003ecc by-sa 3.0 with attribution requiredu003c/au003e u003ca href="https://stackoverflow.com/legal/content-policy"u003e(content policy)u003c/au003e",
    allowUrls: true
    },
    onDemand: true,
    discardSelector: ".discard-answer"
    ,immediatelyShowMarkdownHelp:true
    });


    }
    });














    draft saved

    draft discarded


















    StackExchange.ready(
    function () {
    StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2faskubuntu.com%2fquestions%2f1118777%2fcpu-permanent-throttles-after-5-minutes-of-gaming-util-restart%23new-answer', 'question_page');
    }
    );

    Post as a guest















    Required, but never shown

























    1 Answer
    1






    active

    oldest

    votes








    1 Answer
    1






    active

    oldest

    votes









    active

    oldest

    votes






    active

    oldest

    votes









    0














    Your computer may have some minimal tools in BIOS to prevent overheat damage - and the processor being hot may not translate to "my computer feels hot to the touch"



    I use a set of utilities to manage power and thermal (potential) problem in my laptop. First, install power management tools, and a program to limit CPU speed in severe cases



    sudo apt install tlp thermald


    Tlp has many customizable settings in /etc/default/tlp



    Secondly, install programs to show me the internal temperatures of my computer:



    sudo apt install --install-suggests lm-sensors psensor
    sudo sensors-detect


    just follow the prompts. Add the recommended lines to /etc/modules.



    Now, if you don't want to reboot, you'll have to manually activate the modules.



    sudo modprobe module1 module2


    where module1 etc. = the module names provided from sensors-detect.



    You may also need to add utilities to control the fan in your laptop



    sudo apt install fancontrol
    sudo pwmconfig


    and work your way through the instructions there.



    Finally, run sensors -s to make your fan configuration take effect.



    sudo sensors -s


    Now, you can check your temps.



    sensors


    Now to run fan control, type:



    sudo /usr/sbin/fancontrol &





    share|improve this answer




























      0














      Your computer may have some minimal tools in BIOS to prevent overheat damage - and the processor being hot may not translate to "my computer feels hot to the touch"



      I use a set of utilities to manage power and thermal (potential) problem in my laptop. First, install power management tools, and a program to limit CPU speed in severe cases



      sudo apt install tlp thermald


      Tlp has many customizable settings in /etc/default/tlp



      Secondly, install programs to show me the internal temperatures of my computer:



      sudo apt install --install-suggests lm-sensors psensor
      sudo sensors-detect


      just follow the prompts. Add the recommended lines to /etc/modules.



      Now, if you don't want to reboot, you'll have to manually activate the modules.



      sudo modprobe module1 module2


      where module1 etc. = the module names provided from sensors-detect.



      You may also need to add utilities to control the fan in your laptop



      sudo apt install fancontrol
      sudo pwmconfig


      and work your way through the instructions there.



      Finally, run sensors -s to make your fan configuration take effect.



      sudo sensors -s


      Now, you can check your temps.



      sensors


      Now to run fan control, type:



      sudo /usr/sbin/fancontrol &





      share|improve this answer


























        0












        0








        0







        Your computer may have some minimal tools in BIOS to prevent overheat damage - and the processor being hot may not translate to "my computer feels hot to the touch"



        I use a set of utilities to manage power and thermal (potential) problem in my laptop. First, install power management tools, and a program to limit CPU speed in severe cases



        sudo apt install tlp thermald


        Tlp has many customizable settings in /etc/default/tlp



        Secondly, install programs to show me the internal temperatures of my computer:



        sudo apt install --install-suggests lm-sensors psensor
        sudo sensors-detect


        just follow the prompts. Add the recommended lines to /etc/modules.



        Now, if you don't want to reboot, you'll have to manually activate the modules.



        sudo modprobe module1 module2


        where module1 etc. = the module names provided from sensors-detect.



        You may also need to add utilities to control the fan in your laptop



        sudo apt install fancontrol
        sudo pwmconfig


        and work your way through the instructions there.



        Finally, run sensors -s to make your fan configuration take effect.



        sudo sensors -s


        Now, you can check your temps.



        sensors


        Now to run fan control, type:



        sudo /usr/sbin/fancontrol &





        share|improve this answer













        Your computer may have some minimal tools in BIOS to prevent overheat damage - and the processor being hot may not translate to "my computer feels hot to the touch"



        I use a set of utilities to manage power and thermal (potential) problem in my laptop. First, install power management tools, and a program to limit CPU speed in severe cases



        sudo apt install tlp thermald


        Tlp has many customizable settings in /etc/default/tlp



        Secondly, install programs to show me the internal temperatures of my computer:



        sudo apt install --install-suggests lm-sensors psensor
        sudo sensors-detect


        just follow the prompts. Add the recommended lines to /etc/modules.



        Now, if you don't want to reboot, you'll have to manually activate the modules.



        sudo modprobe module1 module2


        where module1 etc. = the module names provided from sensors-detect.



        You may also need to add utilities to control the fan in your laptop



        sudo apt install fancontrol
        sudo pwmconfig


        and work your way through the instructions there.



        Finally, run sensors -s to make your fan configuration take effect.



        sudo sensors -s


        Now, you can check your temps.



        sensors


        Now to run fan control, type:



        sudo /usr/sbin/fancontrol &






        share|improve this answer












        share|improve this answer



        share|improve this answer










        answered Feb 16 at 16:32









        Charles GreenCharles Green

        14.1k73859




        14.1k73859






























            draft saved

            draft discarded




















































            Thanks for contributing an answer to Ask Ubuntu!


            • Please be sure to answer the question. Provide details and share your research!

            But avoid



            • Asking for help, clarification, or responding to other answers.

            • Making statements based on opinion; back them up with references or personal experience.


            To learn more, see our tips on writing great answers.




            draft saved


            draft discarded














            StackExchange.ready(
            function () {
            StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2faskubuntu.com%2fquestions%2f1118777%2fcpu-permanent-throttles-after-5-minutes-of-gaming-util-restart%23new-answer', 'question_page');
            }
            );

            Post as a guest















            Required, but never shown





















































            Required, but never shown














            Required, but never shown












            Required, but never shown







            Required, but never shown

































            Required, but never shown














            Required, but never shown












            Required, but never shown







            Required, but never shown







            Popular posts from this blog

            How to make a Squid Proxy server?

            Is this a new Fibonacci Identity?

            19世紀