Select between two sources with transistors












1














I'm sorry if this has been asked before but I can't find useful data on this matter.



I have two sources of data and I want to select one of them using transistors.



If I had to guess I'd make the circuit below.
Sadly I never had any electronics courses so maybe I'm missing something obvious here but as I can't find anything about my goal on internet I'd rather ask here.



I just heard about SSRs and they seem to be the best solution for my needs, but I still want to know about how to do this with transistors if this is possible.



Thanks



Circuit



Vout is bottom-right



Edit:
The sources are composite video signals










share|improve this question









New contributor




RenéX is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.




















  • What kind of “sources” are these?
    – user2233709
    2 days ago










  • They are composite video signals
    – RenéX
    yesterday
















1














I'm sorry if this has been asked before but I can't find useful data on this matter.



I have two sources of data and I want to select one of them using transistors.



If I had to guess I'd make the circuit below.
Sadly I never had any electronics courses so maybe I'm missing something obvious here but as I can't find anything about my goal on internet I'd rather ask here.



I just heard about SSRs and they seem to be the best solution for my needs, but I still want to know about how to do this with transistors if this is possible.



Thanks



Circuit



Vout is bottom-right



Edit:
The sources are composite video signals










share|improve this question









New contributor




RenéX is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.




















  • What kind of “sources” are these?
    – user2233709
    2 days ago










  • They are composite video signals
    – RenéX
    yesterday














1












1








1







I'm sorry if this has been asked before but I can't find useful data on this matter.



I have two sources of data and I want to select one of them using transistors.



If I had to guess I'd make the circuit below.
Sadly I never had any electronics courses so maybe I'm missing something obvious here but as I can't find anything about my goal on internet I'd rather ask here.



I just heard about SSRs and they seem to be the best solution for my needs, but I still want to know about how to do this with transistors if this is possible.



Thanks



Circuit



Vout is bottom-right



Edit:
The sources are composite video signals










share|improve this question









New contributor




RenéX is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.











I'm sorry if this has been asked before but I can't find useful data on this matter.



I have two sources of data and I want to select one of them using transistors.



If I had to guess I'd make the circuit below.
Sadly I never had any electronics courses so maybe I'm missing something obvious here but as I can't find anything about my goal on internet I'd rather ask here.



I just heard about SSRs and they seem to be the best solution for my needs, but I still want to know about how to do this with transistors if this is possible.



Thanks



Circuit



Vout is bottom-right



Edit:
The sources are composite video signals







transistors relay voltage-source






share|improve this question









New contributor




RenéX is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.











share|improve this question









New contributor




RenéX is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.









share|improve this question




share|improve this question








edited yesterday







RenéX













New contributor




RenéX is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.









asked 2 days ago









RenéXRenéX

83




83




New contributor




RenéX is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.





New contributor





RenéX is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.






RenéX is a new contributor to this site. Take care in asking for clarification, commenting, and answering.
Check out our Code of Conduct.












  • What kind of “sources” are these?
    – user2233709
    2 days ago










  • They are composite video signals
    – RenéX
    yesterday


















  • What kind of “sources” are these?
    – user2233709
    2 days ago










  • They are composite video signals
    – RenéX
    yesterday
















What kind of “sources” are these?
– user2233709
2 days ago




What kind of “sources” are these?
– user2233709
2 days ago












They are composite video signals
– RenéX
yesterday




They are composite video signals
– RenéX
yesterday










2 Answers
2






active

oldest

votes


















4














If you're selecting between two sources of binary digital data, you should be looking for a digital multiplexer. If you're selecting between two analog signals you should be looking for an analog multiplexer. There are dozens of part numbers of either type available from the major IC vendors, depending on the details of your requirements.



Buying either of these circuits as an IC will probably be lower cost (after accounting for assembly costs) and almost certainly be more reliable and give more consistent results than constructing them out of transistors.






share|improve this answer





















  • Thanks I'll look at these analog multiplexers.
    – RenéX
    yesterday












  • By the time I receive them, is there hope in trying to do something testable (even if far from perfect) with the setup in the OP? I'd like to understand why it doesn't work, be it because of signals stability, frequency response, etc.
    – RenéX
    yesterday










  • To be honest, your circuit could more or less work. Whether it works and/or works well depends on the nature of the sources (Source1 and Source 2), and the load (where is the output signal going). Since you haven't shared that information, I can't say why it didn't work for you.
    – The Photon
    yesterday










  • I wasn't able to try when I asked and I wanted to be sure the circuit was not something stupid. I finally tried and it works perfectly, I didn't expect that. I sure will buy multiplexers though, thanks
    – RenéX
    yesterday










  • @RenéX, now you've shared that these are video signals, I will mention that AFAIK there are ICs specifically sold as video multiplexers. I'm not sure exactly what formats they support or whether they will fit your application.
    – The Photon
    20 hours ago



















0














Part like this will do for analog or digital switching at 3.3V levels.
https://www.analog.com/media/en/technical-documentation/data-sheets/ADG839.pdf



What voltage and current levels are you after?






share|improve this answer





















    Your Answer





    StackExchange.ifUsing("editor", function () {
    return StackExchange.using("mathjaxEditing", function () {
    StackExchange.MarkdownEditor.creationCallbacks.add(function (editor, postfix) {
    StackExchange.mathjaxEditing.prepareWmdForMathJax(editor, postfix, [["\$", "\$"]]);
    });
    });
    }, "mathjax-editing");

    StackExchange.ifUsing("editor", function () {
    return StackExchange.using("schematics", function () {
    StackExchange.schematics.init();
    });
    }, "cicuitlab");

    StackExchange.ready(function() {
    var channelOptions = {
    tags: "".split(" "),
    id: "135"
    };
    initTagRenderer("".split(" "), "".split(" "), channelOptions);

    StackExchange.using("externalEditor", function() {
    // Have to fire editor after snippets, if snippets enabled
    if (StackExchange.settings.snippets.snippetsEnabled) {
    StackExchange.using("snippets", function() {
    createEditor();
    });
    }
    else {
    createEditor();
    }
    });

    function createEditor() {
    StackExchange.prepareEditor({
    heartbeatType: 'answer',
    autoActivateHeartbeat: false,
    convertImagesToLinks: false,
    noModals: true,
    showLowRepImageUploadWarning: true,
    reputationToPostImages: null,
    bindNavPrevention: true,
    postfix: "",
    imageUploader: {
    brandingHtml: "Powered by u003ca class="icon-imgur-white" href="https://imgur.com/"u003eu003c/au003e",
    contentPolicyHtml: "User contributions licensed under u003ca href="https://creativecommons.org/licenses/by-sa/3.0/"u003ecc by-sa 3.0 with attribution requiredu003c/au003e u003ca href="https://stackoverflow.com/legal/content-policy"u003e(content policy)u003c/au003e",
    allowUrls: true
    },
    onDemand: true,
    discardSelector: ".discard-answer"
    ,immediatelyShowMarkdownHelp:true
    });


    }
    });






    RenéX is a new contributor. Be nice, and check out our Code of Conduct.










    draft saved

    draft discarded


















    StackExchange.ready(
    function () {
    StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2felectronics.stackexchange.com%2fquestions%2f415470%2fselect-between-two-sources-with-transistors%23new-answer', 'question_page');
    }
    );

    Post as a guest















    Required, but never shown

























    2 Answers
    2






    active

    oldest

    votes








    2 Answers
    2






    active

    oldest

    votes









    active

    oldest

    votes






    active

    oldest

    votes









    4














    If you're selecting between two sources of binary digital data, you should be looking for a digital multiplexer. If you're selecting between two analog signals you should be looking for an analog multiplexer. There are dozens of part numbers of either type available from the major IC vendors, depending on the details of your requirements.



    Buying either of these circuits as an IC will probably be lower cost (after accounting for assembly costs) and almost certainly be more reliable and give more consistent results than constructing them out of transistors.






    share|improve this answer





















    • Thanks I'll look at these analog multiplexers.
      – RenéX
      yesterday












    • By the time I receive them, is there hope in trying to do something testable (even if far from perfect) with the setup in the OP? I'd like to understand why it doesn't work, be it because of signals stability, frequency response, etc.
      – RenéX
      yesterday










    • To be honest, your circuit could more or less work. Whether it works and/or works well depends on the nature of the sources (Source1 and Source 2), and the load (where is the output signal going). Since you haven't shared that information, I can't say why it didn't work for you.
      – The Photon
      yesterday










    • I wasn't able to try when I asked and I wanted to be sure the circuit was not something stupid. I finally tried and it works perfectly, I didn't expect that. I sure will buy multiplexers though, thanks
      – RenéX
      yesterday










    • @RenéX, now you've shared that these are video signals, I will mention that AFAIK there are ICs specifically sold as video multiplexers. I'm not sure exactly what formats they support or whether they will fit your application.
      – The Photon
      20 hours ago
















    4














    If you're selecting between two sources of binary digital data, you should be looking for a digital multiplexer. If you're selecting between two analog signals you should be looking for an analog multiplexer. There are dozens of part numbers of either type available from the major IC vendors, depending on the details of your requirements.



    Buying either of these circuits as an IC will probably be lower cost (after accounting for assembly costs) and almost certainly be more reliable and give more consistent results than constructing them out of transistors.






    share|improve this answer





















    • Thanks I'll look at these analog multiplexers.
      – RenéX
      yesterday












    • By the time I receive them, is there hope in trying to do something testable (even if far from perfect) with the setup in the OP? I'd like to understand why it doesn't work, be it because of signals stability, frequency response, etc.
      – RenéX
      yesterday










    • To be honest, your circuit could more or less work. Whether it works and/or works well depends on the nature of the sources (Source1 and Source 2), and the load (where is the output signal going). Since you haven't shared that information, I can't say why it didn't work for you.
      – The Photon
      yesterday










    • I wasn't able to try when I asked and I wanted to be sure the circuit was not something stupid. I finally tried and it works perfectly, I didn't expect that. I sure will buy multiplexers though, thanks
      – RenéX
      yesterday










    • @RenéX, now you've shared that these are video signals, I will mention that AFAIK there are ICs specifically sold as video multiplexers. I'm not sure exactly what formats they support or whether they will fit your application.
      – The Photon
      20 hours ago














    4












    4








    4






    If you're selecting between two sources of binary digital data, you should be looking for a digital multiplexer. If you're selecting between two analog signals you should be looking for an analog multiplexer. There are dozens of part numbers of either type available from the major IC vendors, depending on the details of your requirements.



    Buying either of these circuits as an IC will probably be lower cost (after accounting for assembly costs) and almost certainly be more reliable and give more consistent results than constructing them out of transistors.






    share|improve this answer












    If you're selecting between two sources of binary digital data, you should be looking for a digital multiplexer. If you're selecting between two analog signals you should be looking for an analog multiplexer. There are dozens of part numbers of either type available from the major IC vendors, depending on the details of your requirements.



    Buying either of these circuits as an IC will probably be lower cost (after accounting for assembly costs) and almost certainly be more reliable and give more consistent results than constructing them out of transistors.







    share|improve this answer












    share|improve this answer



    share|improve this answer










    answered 2 days ago









    The PhotonThe Photon

    83.5k396194




    83.5k396194












    • Thanks I'll look at these analog multiplexers.
      – RenéX
      yesterday












    • By the time I receive them, is there hope in trying to do something testable (even if far from perfect) with the setup in the OP? I'd like to understand why it doesn't work, be it because of signals stability, frequency response, etc.
      – RenéX
      yesterday










    • To be honest, your circuit could more or less work. Whether it works and/or works well depends on the nature of the sources (Source1 and Source 2), and the load (where is the output signal going). Since you haven't shared that information, I can't say why it didn't work for you.
      – The Photon
      yesterday










    • I wasn't able to try when I asked and I wanted to be sure the circuit was not something stupid. I finally tried and it works perfectly, I didn't expect that. I sure will buy multiplexers though, thanks
      – RenéX
      yesterday










    • @RenéX, now you've shared that these are video signals, I will mention that AFAIK there are ICs specifically sold as video multiplexers. I'm not sure exactly what formats they support or whether they will fit your application.
      – The Photon
      20 hours ago


















    • Thanks I'll look at these analog multiplexers.
      – RenéX
      yesterday












    • By the time I receive them, is there hope in trying to do something testable (even if far from perfect) with the setup in the OP? I'd like to understand why it doesn't work, be it because of signals stability, frequency response, etc.
      – RenéX
      yesterday










    • To be honest, your circuit could more or less work. Whether it works and/or works well depends on the nature of the sources (Source1 and Source 2), and the load (where is the output signal going). Since you haven't shared that information, I can't say why it didn't work for you.
      – The Photon
      yesterday










    • I wasn't able to try when I asked and I wanted to be sure the circuit was not something stupid. I finally tried and it works perfectly, I didn't expect that. I sure will buy multiplexers though, thanks
      – RenéX
      yesterday










    • @RenéX, now you've shared that these are video signals, I will mention that AFAIK there are ICs specifically sold as video multiplexers. I'm not sure exactly what formats they support or whether they will fit your application.
      – The Photon
      20 hours ago
















    Thanks I'll look at these analog multiplexers.
    – RenéX
    yesterday






    Thanks I'll look at these analog multiplexers.
    – RenéX
    yesterday














    By the time I receive them, is there hope in trying to do something testable (even if far from perfect) with the setup in the OP? I'd like to understand why it doesn't work, be it because of signals stability, frequency response, etc.
    – RenéX
    yesterday




    By the time I receive them, is there hope in trying to do something testable (even if far from perfect) with the setup in the OP? I'd like to understand why it doesn't work, be it because of signals stability, frequency response, etc.
    – RenéX
    yesterday












    To be honest, your circuit could more or less work. Whether it works and/or works well depends on the nature of the sources (Source1 and Source 2), and the load (where is the output signal going). Since you haven't shared that information, I can't say why it didn't work for you.
    – The Photon
    yesterday




    To be honest, your circuit could more or less work. Whether it works and/or works well depends on the nature of the sources (Source1 and Source 2), and the load (where is the output signal going). Since you haven't shared that information, I can't say why it didn't work for you.
    – The Photon
    yesterday












    I wasn't able to try when I asked and I wanted to be sure the circuit was not something stupid. I finally tried and it works perfectly, I didn't expect that. I sure will buy multiplexers though, thanks
    – RenéX
    yesterday




    I wasn't able to try when I asked and I wanted to be sure the circuit was not something stupid. I finally tried and it works perfectly, I didn't expect that. I sure will buy multiplexers though, thanks
    – RenéX
    yesterday












    @RenéX, now you've shared that these are video signals, I will mention that AFAIK there are ICs specifically sold as video multiplexers. I'm not sure exactly what formats they support or whether they will fit your application.
    – The Photon
    20 hours ago




    @RenéX, now you've shared that these are video signals, I will mention that AFAIK there are ICs specifically sold as video multiplexers. I'm not sure exactly what formats they support or whether they will fit your application.
    – The Photon
    20 hours ago













    0














    Part like this will do for analog or digital switching at 3.3V levels.
    https://www.analog.com/media/en/technical-documentation/data-sheets/ADG839.pdf



    What voltage and current levels are you after?






    share|improve this answer


























      0














      Part like this will do for analog or digital switching at 3.3V levels.
      https://www.analog.com/media/en/technical-documentation/data-sheets/ADG839.pdf



      What voltage and current levels are you after?






      share|improve this answer
























        0












        0








        0






        Part like this will do for analog or digital switching at 3.3V levels.
        https://www.analog.com/media/en/technical-documentation/data-sheets/ADG839.pdf



        What voltage and current levels are you after?






        share|improve this answer












        Part like this will do for analog or digital switching at 3.3V levels.
        https://www.analog.com/media/en/technical-documentation/data-sheets/ADG839.pdf



        What voltage and current levels are you after?







        share|improve this answer












        share|improve this answer



        share|improve this answer










        answered 2 days ago









        CrossRoadsCrossRoads

        1,2698




        1,2698






















            RenéX is a new contributor. Be nice, and check out our Code of Conduct.










            draft saved

            draft discarded


















            RenéX is a new contributor. Be nice, and check out our Code of Conduct.













            RenéX is a new contributor. Be nice, and check out our Code of Conduct.












            RenéX is a new contributor. Be nice, and check out our Code of Conduct.
















            Thanks for contributing an answer to Electrical Engineering Stack Exchange!


            • Please be sure to answer the question. Provide details and share your research!

            But avoid



            • Asking for help, clarification, or responding to other answers.

            • Making statements based on opinion; back them up with references or personal experience.


            Use MathJax to format equations. MathJax reference.


            To learn more, see our tips on writing great answers.





            Some of your past answers have not been well-received, and you're in danger of being blocked from answering.


            Please pay close attention to the following guidance:


            • Please be sure to answer the question. Provide details and share your research!

            But avoid



            • Asking for help, clarification, or responding to other answers.

            • Making statements based on opinion; back them up with references or personal experience.


            To learn more, see our tips on writing great answers.




            draft saved


            draft discarded














            StackExchange.ready(
            function () {
            StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2felectronics.stackexchange.com%2fquestions%2f415470%2fselect-between-two-sources-with-transistors%23new-answer', 'question_page');
            }
            );

            Post as a guest















            Required, but never shown





















































            Required, but never shown














            Required, but never shown












            Required, but never shown







            Required, but never shown

































            Required, but never shown














            Required, but never shown












            Required, but never shown







            Required, but never shown







            Popular posts from this blog

            How to make a Squid Proxy server?

            Is this a new Fibonacci Identity?

            19世紀