alsamixer / pulseaudio choose internal mic over mic jack
I have laptops running Debian stretch / pulseaudio version 10.0-1 on which I'd like to choose the internal microphone over the mic jack.
When I plug my headphone which includes a microphone through the jack, only the microphone of the headset works and I don't find a way to switch to the built-in one.
$ amixer -c0 controls | grep -i mic
numid=16,iface=CARD,name='Internal Mic Phantom Jack'
numid=15,iface=CARD,name='Mic Jack'
numid=11,iface=MIXER,name='Mic Boost Volume'
numid=7,iface=MIXER,name='Mic Playback Switch'
numid=6,iface=MIXER,name='Mic Playback Volume'
numid=12,iface=MIXER,name='Internal Mic Boost Volume'
My sound card is an HDA Intel PCH on all my laptops.
I tried to disable the iface=CARD numid=15 but I get a Operation not permitted:
$ amixer -c0 cset numid=15 off
amixer: Control hw:0 element write error: Operation not permitted
EDIT:
As suggested in comment, I searched in pavucontrol and pulseaudio settings but can't find anything that solve my problem.
EDIT 2:
In order to have further information on the codecs, I paste the output of the cat /proc/asound/card*/codec#* command:
Codec: Realtek ALC293
Address: 0
AFG Function Id: 0x1 (unsol 1)
Vendor Id: 0x10ec0293
Subsystem Id: 0x17aa504b
Revision Id: 0x100003
No Modem Function Group found
Default PCM:
rates [0x5f0]: 32000 44100 48000 88200 96000 192000
bits [0xe]: 16 20 24
formats [0x1]: PCM
Default Amp-In caps: N/A
Default Amp-Out caps: N/A
State of AFG node 0x01:
Power states: D0 D1 D2 D3 D3cold CLKSTOP EPSS
Power: setting=D0, actual=D0
GPIO: io=5, o=0, i=0, unsolicited=1, wake=0
IO[0]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0
IO[1]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0
IO[2]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0
IO[3]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0
IO[4]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0
Node 0x02 [Audio Output] wcaps 0x41d: Stereo Amp-Out
Control: name="Speaker Playback Volume", index=0, device=0
ControlAmp: chs=3, dir=Out, idx=0, ofs=0
Device: name="ALC293 Analog", type="Audio", device=0
Amp-Out caps: ofs=0x57, nsteps=0x57, stepsize=0x02, mute=0
Amp-Out vals: [0x2b 0x2b]
Converter: stream=1, channel=0
PCM:
rates [0x560]: 44100 48000 96000 192000
bits [0xe]: 16 20 24
formats [0x1]: PCM
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Node 0x03 [Audio Output] wcaps 0x41d: Stereo Amp-Out
Control: name="Headphone Playback Volume", index=0, device=0
ControlAmp: chs=3, dir=Out, idx=0, ofs=0
Amp-Out caps: ofs=0x57, nsteps=0x57, stepsize=0x02, mute=0
Amp-Out vals: [0x00 0x00]
Converter: stream=1, channel=0
PCM:
rates [0x560]: 44100 48000 96000 192000
bits [0xe]: 16 20 24
formats [0x1]: PCM
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Node 0x04 [Vendor Defined Widget] wcaps 0xf00000: Mono
Node 0x05 [Vendor Defined Widget] wcaps 0xf00000: Mono
Node 0x06 [Audio Output] wcaps 0x611: Stereo Digital
Converter: stream=0, channel=0
Digital:
Digital category: 0x0
IEC Coding Type: 0x0
PCM:
rates [0x5f0]: 32000 44100 48000 88200 96000 192000
bits [0xe]: 16 20 24
formats [0x1]: PCM
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Node 0x07 [Audio Input] wcaps 0x10051b: Stereo Amp-In
Amp-In caps: ofs=0x17, nsteps=0x3f, stepsize=0x02, mute=1
Amp-In vals: [0x97 0x97]
Converter: stream=0, channel=0
SDI-Select: 0
PCM:
rates [0x560]: 44100 48000 96000 192000
bits [0xe]: 16 20 24
formats [0x1]: PCM
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Connection: 1
0x24
Node 0x08 [Audio Input] wcaps 0x10051b: Stereo Amp-In
Amp-In caps: ofs=0x17, nsteps=0x3f, stepsize=0x02, mute=1
Amp-In vals: [0x97 0x97]
Converter: stream=0, channel=0
SDI-Select: 0
PCM:
rates [0x560]: 44100 48000 96000 192000
bits [0xe]: 16 20 24
formats [0x1]: PCM
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Connection: 1
0x23
Node 0x09 [Audio Input] wcaps 0x10051b: Stereo Amp-In
Control: name="Capture Volume", index=0, device=0
ControlAmp: chs=3, dir=In, idx=0, ofs=0
Control: name="Capture Switch", index=0, device=0
ControlAmp: chs=3, dir=In, idx=0, ofs=0
Device: name="ALC293 Analog", type="Audio", device=0
Amp-In caps: ofs=0x17, nsteps=0x3f, stepsize=0x02, mute=1
Amp-In vals: [0x3e 0x3e]
Converter: stream=1, channel=0
SDI-Select: 0
PCM:
rates [0x560]: 44100 48000 96000 192000
bits [0xe]: 16 20 24
formats [0x1]: PCM
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Connection: 1
0x22
Node 0x0a [Vendor Defined Widget] wcaps 0xf00000: Mono
Node 0x0b [Audio Mixer] wcaps 0x20010b: Stereo Amp-In
Control: name="Dock Mic Playback Volume", index=0, device=0
ControlAmp: chs=3, dir=In, idx=1, ofs=0
Control: name="Dock Mic Playback Switch", index=0, device=0
ControlAmp: chs=3, dir=In, idx=1, ofs=0
Control: name="Mic Playback Volume", index=0, device=0
ControlAmp: chs=3, dir=In, idx=2, ofs=0
Control: name="Mic Playback Switch", index=0, device=0
ControlAmp: chs=3, dir=In, idx=2, ofs=0
Control: name="Beep Playback Volume", index=0, device=0
ControlAmp: chs=3, dir=In, idx=4, ofs=0
Control: name="Beep Playback Switch", index=0, device=0
ControlAmp: chs=3, dir=In, idx=4, ofs=0
Amp-In caps: ofs=0x17, nsteps=0x1f, stepsize=0x05, mute=1
Amp-In vals: [0x80 0x80] [0x00 0x00] [0x16 0x16] [0x80 0x80] [0x80 0x80]
Connection: 5
0x18 0x19 0x1a 0x1b 0x1d
Node 0x0c [Audio Mixer] wcaps 0x20010b: Stereo Amp-In
Amp-In caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-In vals: [0x00 0x00] [0x80 0x80]
Connection: 2
0x02 0x0b
Node 0x0d [Audio Mixer] wcaps 0x20010b: Stereo Amp-In
Amp-In caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-In vals: [0x00 0x00] [0x80 0x80]
Connection: 2
0x03 0x0b
Node 0x0e [Vendor Defined Widget] wcaps 0xf00000: Mono
Node 0x0f [Vendor Defined Widget] wcaps 0xf00000: Mono
Node 0x10 [Vendor Defined Widget] wcaps 0xf00000: Mono
Node 0x11 [Vendor Defined Widget] wcaps 0xf00000: Mono
Node 0x12 [Pin Complex] wcaps 0x40040b: Stereo Amp-In
Control: name="Internal Mic Boost Volume", index=0, device=0
ControlAmp: chs=3, dir=In, idx=0, ofs=0
Amp-In caps: ofs=0x00, nsteps=0x03, stepsize=0x27, mute=0
Amp-In vals: [0x00 0x00]
Pincap 0x00000020: IN
Pin Default 0x90a60130: [Fixed] Mic at Int N/A
Conn = Digital, Color = Unknown
DefAssociation = 0x3, Sequence = 0x0
Misc = NO_PRESENCE
Pin-ctls: 0x20: IN
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Node 0x13 [Pin Complex] wcaps 0x40040b: Stereo Amp-In
Amp-In caps: ofs=0x00, nsteps=0x03, stepsize=0x27, mute=0
Amp-In vals: [0x00 0x00]
Pincap 0x00000020: IN
Pin Default 0x40000000: [N/A] Line Out at Ext N/A
Conn = Unknown, Color = Unknown
DefAssociation = 0x0, Sequence = 0x0
Pin-ctls: 0x00:
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Node 0x14 [Pin Complex] wcaps 0x40058d: Stereo Amp-Out
Control: name="Speaker Playback Switch", index=0, device=0
ControlAmp: chs=3, dir=Out, idx=0, ofs=0
Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-Out vals: [0x80 0x80]
Pincap 0x00010010: OUT EAPD
EAPD 0x2: EAPD
Pin Default 0x90170110: [Fixed] Speaker at Int N/A
Conn = Analog, Color = Unknown
DefAssociation = 0x1, Sequence = 0x0
Misc = NO_PRESENCE
Pin-ctls: 0x40: OUT
Unsolicited: tag=00, enabled=0
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Connection: 1
0x0c
Node 0x15 [Pin Complex] wcaps 0x40058d: Stereo Amp-Out
Control: name="Headphone Playback Switch", index=1, device=0
ControlAmp: chs=3, dir=Out, idx=0, ofs=0
Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-Out vals: [0x00 0x00]
Pincap 0x0001001c: OUT HP EAPD Detect
EAPD 0x2: EAPD
Pin Default 0x03211040: [Jack] HP Out at Ext Left
Conn = 1/8, Color = Black
DefAssociation = 0x4, Sequence = 0x0
Pin-ctls: 0xc0: OUT HP
Unsolicited: tag=02, enabled=1
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Connection: 2
0x0c 0x0d*
Node 0x16 [Pin Complex] wcaps 0x40058d: Stereo Amp-Out
Control: name="Headphone Playback Switch", index=0, device=0
ControlAmp: chs=3, dir=Out, idx=0, ofs=0
Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-Out vals: [0x80 0x80]
Pincap 0x0001001c: OUT HP EAPD Detect
EAPD 0x2: EAPD
Pin Default 0x411111f0: [N/A] Speaker at Ext Rear
Conn = 1/8, Color = Black
DefAssociation = 0xf, Sequence = 0x0
Misc = NO_PRESENCE
Pin-ctls: 0xc0: OUT HP
Unsolicited: tag=01, enabled=1
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Connection: 2
0x0c 0x0d*
Node 0x17 [Vendor Defined Widget] wcaps 0xf00000: Mono
Node 0x18 [Pin Complex] wcaps 0x40058f: Stereo Amp-In Amp-Out
Amp-In caps: ofs=0x00, nsteps=0x03, stepsize=0x27, mute=0
Amp-In vals: [0x00 0x00]
Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-Out vals: [0x80 0x80]
Pincap 0x0000373c: IN OUT HP Detect
Vref caps: HIZ 50 GRD 80 100
Pin Default 0x411111f0: [N/A] Speaker at Ext Rear
Conn = 1/8, Color = Black
DefAssociation = 0xf, Sequence = 0x0
Misc = NO_PRESENCE
Pin-ctls: 0x00: VREF_HIZ
Unsolicited: tag=00, enabled=0
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Connection: 2
0x0c* 0x0d
Node 0x19 [Pin Complex] wcaps 0x40048b: Stereo Amp-In
Control: name="Dock Mic Boost Volume", index=0, device=0
ControlAmp: chs=3, dir=In, idx=0, ofs=0
Amp-In caps: ofs=0x00, nsteps=0x03, stepsize=0x27, mute=0
Amp-In vals: [0x00 0x00]
Pincap 0x00000024: IN Detect
Pin Default 0x411111f0: [N/A] Speaker at Ext Rear
Conn = 1/8, Color = Black
DefAssociation = 0xf, Sequence = 0x0
Misc = NO_PRESENCE
Pin-ctls: 0x20: IN
Unsolicited: tag=03, enabled=1
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Node 0x1a [Pin Complex] wcaps 0x40048b: Stereo Amp-In
Control: name="Mic Boost Volume", index=0, device=0
ControlAmp: chs=3, dir=In, idx=0, ofs=0
Amp-In caps: ofs=0x00, nsteps=0x03, stepsize=0x27, mute=0
Amp-In vals: [0x00 0x00]
Pincap 0x00003724: IN Detect
Vref caps: HIZ 50 GRD 80 100
Pin Default 0x03a11020: [Jack] Mic at Ext Left
Conn = 1/8, Color = Black
DefAssociation = 0x2, Sequence = 0x0
Pin-ctls: 0x24: IN VREF_80
Unsolicited: tag=04, enabled=1
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Node 0x1b [Pin Complex] wcaps 0x40058f: Stereo Amp-In Amp-Out
Amp-In caps: ofs=0x00, nsteps=0x03, stepsize=0x27, mute=0
Amp-In vals: [0x00 0x00]
Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-Out vals: [0x80 0x80]
Pincap 0x0000373c: IN OUT HP Detect
Vref caps: HIZ 50 GRD 80 100
Pin Default 0x411111f0: [N/A] Speaker at Ext Rear
Conn = 1/8, Color = Black
DefAssociation = 0xf, Sequence = 0x0
Misc = NO_PRESENCE
Pin-ctls: 0x20: IN VREF_HIZ
Unsolicited: tag=00, enabled=0
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Connection: 2
0x0c* 0x0d
Node 0x1c [Vendor Defined Widget] wcaps 0xf00000: Mono
Node 0x1d [Pin Complex] wcaps 0x400400: Mono
Pincap 0x00000020: IN
Pin Default 0x40738105: [N/A] Modem Hand at Ext N/A
Conn = ATAPI, Color = Purple
DefAssociation = 0x0, Sequence = 0x5
Misc = NO_PRESENCE
Pin-ctls: 0x20: IN
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Node 0x1e [Pin Complex] wcaps 0x400781: Stereo Digital
Pincap 0x00000014: OUT Detect
Pin Default 0x411111f0: [N/A] Speaker at Ext Rear
Conn = 1/8, Color = Black
DefAssociation = 0xf, Sequence = 0x0
Misc = NO_PRESENCE
Pin-ctls: 0x40: OUT
Unsolicited: tag=00, enabled=0
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Connection: 1
0x06
Node 0x1f [Vendor Defined Widget] wcaps 0xf00000: Mono
Node 0x20 [Vendor Defined Widget] wcaps 0xf00040: Mono
Processing caps: benign=0, ncoeff=90
Node 0x21 [Vendor Defined Widget] wcaps 0xf00000: Mono
Node 0x22 [Audio Selector] wcaps 0x300101: Stereo
Connection: 8
0x18 0x19 0x1a 0x1b 0x1d 0x0b 0x12* 0x13
Node 0x23 [Audio Selector] wcaps 0x300101: Stereo
Connection: 6
0x18* 0x19 0x1a 0x1b 0x1d 0x0b
Node 0x24 [Audio Selector] wcaps 0x300101: Stereo
Connection: 2
0x12* 0x13
Codec: Intel Skylake HDMI
Address: 2
AFG Function Id: 0x1 (unsol 0)
Vendor Id: 0x80862809
Subsystem Id: 0x80860101
Revision Id: 0x100000
No Modem Function Group found
Default PCM:
rates [0x0]:
bits [0x0]:
formats [0x0]:
Default Amp-In caps: N/A
Default Amp-Out caps: N/A
State of AFG node 0x01:
Power states: D0 D3 CLKSTOP EPSS
Power: setting=D0, actual=D0, Clock-stop-OK
GPIO: io=0, o=0, i=0, unsolicited=0, wake=0
Node 0x02 [Audio Output] wcaps 0x6611: 8-Channels Digital
Converter: stream=0, channel=0
Digital: Enabled KAE
Digital category: 0x0
IEC Coding Type: 0x0
PCM:
rates [0x7f0]: 32000 44100 48000 88200 96000 176400 192000
bits [0x1a]: 16 24 32
formats [0x5]: PCM AC3
Power states: D0 D3 EPSS
Power: setting=D0, actual=D0
Node 0x03 [Audio Output] wcaps 0x6611: 8-Channels Digital
Converter: stream=0, channel=0
Digital: Enabled KAE
Digital category: 0x0
IEC Coding Type: 0x0
PCM:
rates [0x7f0]: 32000 44100 48000 88200 96000 176400 192000
bits [0x1a]: 16 24 32
formats [0x5]: PCM AC3
Power states: D0 D3 EPSS
Power: setting=D0, actual=D0
Node 0x04 [Audio Output] wcaps 0x6611: 8-Channels Digital
Converter: stream=0, channel=0
Digital: Enabled KAE
Digital category: 0x0
IEC Coding Type: 0x0
PCM:
rates [0x7f0]: 32000 44100 48000 88200 96000 176400 192000
bits [0x1a]: 16 24 32
formats [0x5]: PCM AC3
Power states: D0 D3 EPSS
Power: setting=D0, actual=D0
Node 0x05 [Pin Complex] wcaps 0x40778d: 8-Channels Digital Amp-Out CP
Control: name="IEC958 Playback Con Mask", index=0, device=0
Control: name="IEC958 Playback Pro Mask", index=0, device=0
Control: name="IEC958 Playback Default", index=0, device=0
Control: name="IEC958 Playback Switch", index=0, device=0
Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-Out vals: [0x00 0x00]
Pincap 0x0b000094: OUT Detect HBR HDMI DP
Pin Default 0x18560010: [Jack] Digital Out at Int HDMI
Conn = Digital, Color = Unknown
DefAssociation = 0x1, Sequence = 0x0
Pin-ctls: 0x00:
Unsolicited: tag=00, enabled=0
Power states: D0 D3 EPSS
Power: setting=D0, actual=D0
Devices: 0
Connection: 0
In-driver Connection: 3
0x02 0x03 0x04
Node 0x06 [Pin Complex] wcaps 0x40778d: 8-Channels Digital Amp-Out CP
Control: name="IEC958 Playback Con Mask", index=1, device=0
Control: name="IEC958 Playback Pro Mask", index=1, device=0
Control: name="IEC958 Playback Default", index=1, device=0
Control: name="IEC958 Playback Switch", index=1, device=0
Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-Out vals: [0x00 0x00]
Pincap 0x0b000094: OUT Detect HBR HDMI DP
Pin Default 0x18560010: [Jack] Digital Out at Int HDMI
Conn = Digital, Color = Unknown
DefAssociation = 0x1, Sequence = 0x0
Pin-ctls: 0x00:
Unsolicited: tag=00, enabled=0
Power states: D0 D3 EPSS
Power: setting=D0, actual=D0
Devices: 0
Connection: 0
In-driver Connection: 3
0x02 0x03 0x04
Node 0x07 [Pin Complex] wcaps 0x40778d: 8-Channels Digital Amp-Out CP
Control: name="IEC958 Playback Con Mask", index=2, device=0
Control: name="IEC958 Playback Pro Mask", index=2, device=0
Control: name="IEC958 Playback Default", index=2, device=0
Control: name="IEC958 Playback Switch", index=2, device=0
Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-Out vals: [0x00 0x00]
Pincap 0x0b000094: OUT Detect HBR HDMI DP
Pin Default 0x18560010: [Jack] Digital Out at Int HDMI
Conn = Digital, Color = Unknown
DefAssociation = 0x1, Sequence = 0x0
Pin-ctls: 0x00:
Unsolicited: tag=00, enabled=0
Power states: D0 D3 EPSS
Power: setting=D0, actual=D0
Devices: 0
Connection: 0
In-driver Connection: 3
0x02 0x03 0x04
Node 0x08 [Vendor Defined Widget] wcaps 0xf00000: Mono
Edit 2:
I have more information about amixer, with and without the microphone plugged in as asked in comment, with these commands:
cat /proc/asound/card0/codec#0 > /tmp/with_mic.codec0.dump
amixer -c0 contents > /tmp/with_mic.contents.dump
# unplug the microphone
cat /proc/asound/card0/codec#0 > /tmp/without_mic.codec0.dump
amixer -c0 contents > /tmp/without_mic.contents.dump
Now if I do a diff on the codec0 files, I find as guessed by @dirkt that Node 0x22 switch from 0x12* to 0x1a.
Node 0x22 [Audio Selector] wcaps 0x300101: Stereo
Connection: 8
- 0x18 0x19 0x1a* 0x1b 0x1d 0x0b 0x12 0x13
+ 0x18 0x19 0x1a 0x1b 0x1d 0x0b 0x12* 0x13
Now I find the only Auto-Mute Mode control, and disabled it.
$ amixer -c0 cget numid=11
numid=11,iface=MIXER,name='Auto-Mute Mode'
; type=ENUMERATED,access=rw------,values=1,items=2
; Item #0 'Disabled'
; Item #1 'Enabled'
: values=1
$ amixer -c0 cset numid=11 0
numid=11,iface=MIXER,name='Auto-Mute Mode'
; type=ENUMERATED,access=rw------,values=1,items=2
; Item #0 'Disabled'
; Item #1 'Enabled'
: values=0
I reproduce the dump with and without the microphone plugged in, but I still have in the difference the switch on the Node 22.
alsa pulseaudio jack
asked Mar 6 '17 at 22:58
aRkadeFRaRkadeFR
1457
bumped to the homepage by Community♦ 2 days ago
This question has answers that may be good or bad; the system has marked it active so that they can be reviewed.
add a comment |
I have laptops running Debian stretch / pulseaudio version 10.0-1 on which I'd like to choose the internal microphone over the mic jack.
When I plug my headphone which includes a microphone through the jack, only the microphone of the headset works and I don't find a way to switch to the built-in one.
$ amixer -c0 controls | grep -i mic
numid=16,iface=CARD,name='Internal Mic Phantom Jack'
numid=15,iface=CARD,name='Mic Jack'
numid=11,iface=MIXER,name='Mic Boost Volume'
numid=7,iface=MIXER,name='Mic Playback Switch'
numid=6,iface=MIXER,name='Mic Playback Volume'
numid=12,iface=MIXER,name='Internal Mic Boost Volume'
My sound card is an HDA Intel PCH on all my laptops.
I tried to disable the iface=CARD numid=15 but I get a Operation not permitted:
$ amixer -c0 cset numid=15 off
amixer: Control hw:0 element write error: Operation not permitted
EDIT:
As suggested in comment, I searched in pavucontrol and pulseaudio settings but can't find anything that solve my problem.
EDIT 2:
In order to have further information on the codecs, I paste the output of the cat /proc/asound/card*/codec#* command:
Codec: Realtek ALC293
Address: 0
AFG Function Id: 0x1 (unsol 1)
Vendor Id: 0x10ec0293
Subsystem Id: 0x17aa504b
Revision Id: 0x100003
No Modem Function Group found
Default PCM:
rates [0x5f0]: 32000 44100 48000 88200 96000 192000
bits [0xe]: 16 20 24
formats [0x1]: PCM
Default Amp-In caps: N/A
Default Amp-Out caps: N/A
State of AFG node 0x01:
Power states: D0 D1 D2 D3 D3cold CLKSTOP EPSS
Power: setting=D0, actual=D0
GPIO: io=5, o=0, i=0, unsolicited=1, wake=0
IO[0]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0
IO[1]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0
IO[2]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0
IO[3]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0
IO[4]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0
Node 0x02 [Audio Output] wcaps 0x41d: Stereo Amp-Out
Control: name="Speaker Playback Volume", index=0, device=0
ControlAmp: chs=3, dir=Out, idx=0, ofs=0
Device: name="ALC293 Analog", type="Audio", device=0
Amp-Out caps: ofs=0x57, nsteps=0x57, stepsize=0x02, mute=0
Amp-Out vals: [0x2b 0x2b]
Converter: stream=1, channel=0
PCM:
rates [0x560]: 44100 48000 96000 192000
bits [0xe]: 16 20 24
formats [0x1]: PCM
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Node 0x03 [Audio Output] wcaps 0x41d: Stereo Amp-Out
Control: name="Headphone Playback Volume", index=0, device=0
ControlAmp: chs=3, dir=Out, idx=0, ofs=0
Amp-Out caps: ofs=0x57, nsteps=0x57, stepsize=0x02, mute=0
Amp-Out vals: [0x00 0x00]
Converter: stream=1, channel=0
PCM:
rates [0x560]: 44100 48000 96000 192000
bits [0xe]: 16 20 24
formats [0x1]: PCM
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Node 0x04 [Vendor Defined Widget] wcaps 0xf00000: Mono
Node 0x05 [Vendor Defined Widget] wcaps 0xf00000: Mono
Node 0x06 [Audio Output] wcaps 0x611: Stereo Digital
Converter: stream=0, channel=0
Digital:
Digital category: 0x0
IEC Coding Type: 0x0
PCM:
rates [0x5f0]: 32000 44100 48000 88200 96000 192000
bits [0xe]: 16 20 24
formats [0x1]: PCM
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Node 0x07 [Audio Input] wcaps 0x10051b: Stereo Amp-In
Amp-In caps: ofs=0x17, nsteps=0x3f, stepsize=0x02, mute=1
Amp-In vals: [0x97 0x97]
Converter: stream=0, channel=0
SDI-Select: 0
PCM:
rates [0x560]: 44100 48000 96000 192000
bits [0xe]: 16 20 24
formats [0x1]: PCM
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Connection: 1
0x24
Node 0x08 [Audio Input] wcaps 0x10051b: Stereo Amp-In
Amp-In caps: ofs=0x17, nsteps=0x3f, stepsize=0x02, mute=1
Amp-In vals: [0x97 0x97]
Converter: stream=0, channel=0
SDI-Select: 0
PCM:
rates [0x560]: 44100 48000 96000 192000
bits [0xe]: 16 20 24
formats [0x1]: PCM
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Connection: 1
0x23
Node 0x09 [Audio Input] wcaps 0x10051b: Stereo Amp-In
Control: name="Capture Volume", index=0, device=0
ControlAmp: chs=3, dir=In, idx=0, ofs=0
Control: name="Capture Switch", index=0, device=0
ControlAmp: chs=3, dir=In, idx=0, ofs=0
Device: name="ALC293 Analog", type="Audio", device=0
Amp-In caps: ofs=0x17, nsteps=0x3f, stepsize=0x02, mute=1
Amp-In vals: [0x3e 0x3e]
Converter: stream=1, channel=0
SDI-Select: 0
PCM:
rates [0x560]: 44100 48000 96000 192000
bits [0xe]: 16 20 24
formats [0x1]: PCM
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Connection: 1
0x22
Node 0x0a [Vendor Defined Widget] wcaps 0xf00000: Mono
Node 0x0b [Audio Mixer] wcaps 0x20010b: Stereo Amp-In
Control: name="Dock Mic Playback Volume", index=0, device=0
ControlAmp: chs=3, dir=In, idx=1, ofs=0
Control: name="Dock Mic Playback Switch", index=0, device=0
ControlAmp: chs=3, dir=In, idx=1, ofs=0
Control: name="Mic Playback Volume", index=0, device=0
ControlAmp: chs=3, dir=In, idx=2, ofs=0
Control: name="Mic Playback Switch", index=0, device=0
ControlAmp: chs=3, dir=In, idx=2, ofs=0
Control: name="Beep Playback Volume", index=0, device=0
ControlAmp: chs=3, dir=In, idx=4, ofs=0
Control: name="Beep Playback Switch", index=0, device=0
ControlAmp: chs=3, dir=In, idx=4, ofs=0
Amp-In caps: ofs=0x17, nsteps=0x1f, stepsize=0x05, mute=1
Amp-In vals: [0x80 0x80] [0x00 0x00] [0x16 0x16] [0x80 0x80] [0x80 0x80]
Connection: 5
0x18 0x19 0x1a 0x1b 0x1d
Node 0x0c [Audio Mixer] wcaps 0x20010b: Stereo Amp-In
Amp-In caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-In vals: [0x00 0x00] [0x80 0x80]
Connection: 2
0x02 0x0b
Node 0x0d [Audio Mixer] wcaps 0x20010b: Stereo Amp-In
Amp-In caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-In vals: [0x00 0x00] [0x80 0x80]
Connection: 2
0x03 0x0b
Node 0x0e [Vendor Defined Widget] wcaps 0xf00000: Mono
Node 0x0f [Vendor Defined Widget] wcaps 0xf00000: Mono
Node 0x10 [Vendor Defined Widget] wcaps 0xf00000: Mono
Node 0x11 [Vendor Defined Widget] wcaps 0xf00000: Mono
Node 0x12 [Pin Complex] wcaps 0x40040b: Stereo Amp-In
Control: name="Internal Mic Boost Volume", index=0, device=0
ControlAmp: chs=3, dir=In, idx=0, ofs=0
Amp-In caps: ofs=0x00, nsteps=0x03, stepsize=0x27, mute=0
Amp-In vals: [0x00 0x00]
Pincap 0x00000020: IN
Pin Default 0x90a60130: [Fixed] Mic at Int N/A
Conn = Digital, Color = Unknown
DefAssociation = 0x3, Sequence = 0x0
Misc = NO_PRESENCE
Pin-ctls: 0x20: IN
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Node 0x13 [Pin Complex] wcaps 0x40040b: Stereo Amp-In
Amp-In caps: ofs=0x00, nsteps=0x03, stepsize=0x27, mute=0
Amp-In vals: [0x00 0x00]
Pincap 0x00000020: IN
Pin Default 0x40000000: [N/A] Line Out at Ext N/A
Conn = Unknown, Color = Unknown
DefAssociation = 0x0, Sequence = 0x0
Pin-ctls: 0x00:
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Node 0x14 [Pin Complex] wcaps 0x40058d: Stereo Amp-Out
Control: name="Speaker Playback Switch", index=0, device=0
ControlAmp: chs=3, dir=Out, idx=0, ofs=0
Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-Out vals: [0x80 0x80]
Pincap 0x00010010: OUT EAPD
EAPD 0x2: EAPD
Pin Default 0x90170110: [Fixed] Speaker at Int N/A
Conn = Analog, Color = Unknown
DefAssociation = 0x1, Sequence = 0x0
Misc = NO_PRESENCE
Pin-ctls: 0x40: OUT
Unsolicited: tag=00, enabled=0
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Connection: 1
0x0c
Node 0x15 [Pin Complex] wcaps 0x40058d: Stereo Amp-Out
Control: name="Headphone Playback Switch", index=1, device=0
ControlAmp: chs=3, dir=Out, idx=0, ofs=0
Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-Out vals: [0x00 0x00]
Pincap 0x0001001c: OUT HP EAPD Detect
EAPD 0x2: EAPD
Pin Default 0x03211040: [Jack] HP Out at Ext Left
Conn = 1/8, Color = Black
DefAssociation = 0x4, Sequence = 0x0
Pin-ctls: 0xc0: OUT HP
Unsolicited: tag=02, enabled=1
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Connection: 2
0x0c 0x0d*
Node 0x16 [Pin Complex] wcaps 0x40058d: Stereo Amp-Out
Control: name="Headphone Playback Switch", index=0, device=0
ControlAmp: chs=3, dir=Out, idx=0, ofs=0
Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-Out vals: [0x80 0x80]
Pincap 0x0001001c: OUT HP EAPD Detect
EAPD 0x2: EAPD
Pin Default 0x411111f0: [N/A] Speaker at Ext Rear
Conn = 1/8, Color = Black
DefAssociation = 0xf, Sequence = 0x0
Misc = NO_PRESENCE
Pin-ctls: 0xc0: OUT HP
Unsolicited: tag=01, enabled=1
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Connection: 2
0x0c 0x0d*
Node 0x17 [Vendor Defined Widget] wcaps 0xf00000: Mono
Node 0x18 [Pin Complex] wcaps 0x40058f: Stereo Amp-In Amp-Out
Amp-In caps: ofs=0x00, nsteps=0x03, stepsize=0x27, mute=0
Amp-In vals: [0x00 0x00]
Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-Out vals: [0x80 0x80]
Pincap 0x0000373c: IN OUT HP Detect
Vref caps: HIZ 50 GRD 80 100
Pin Default 0x411111f0: [N/A] Speaker at Ext Rear
Conn = 1/8, Color = Black
DefAssociation = 0xf, Sequence = 0x0
Misc = NO_PRESENCE
Pin-ctls: 0x00: VREF_HIZ
Unsolicited: tag=00, enabled=0
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Connection: 2
0x0c* 0x0d
Node 0x19 [Pin Complex] wcaps 0x40048b: Stereo Amp-In
Control: name="Dock Mic Boost Volume", index=0, device=0
ControlAmp: chs=3, dir=In, idx=0, ofs=0
Amp-In caps: ofs=0x00, nsteps=0x03, stepsize=0x27, mute=0
Amp-In vals: [0x00 0x00]
Pincap 0x00000024: IN Detect
Pin Default 0x411111f0: [N/A] Speaker at Ext Rear
Conn = 1/8, Color = Black
DefAssociation = 0xf, Sequence = 0x0
Misc = NO_PRESENCE
Pin-ctls: 0x20: IN
Unsolicited: tag=03, enabled=1
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Node 0x1a [Pin Complex] wcaps 0x40048b: Stereo Amp-In
Control: name="Mic Boost Volume", index=0, device=0
ControlAmp: chs=3, dir=In, idx=0, ofs=0
Amp-In caps: ofs=0x00, nsteps=0x03, stepsize=0x27, mute=0
Amp-In vals: [0x00 0x00]
Pincap 0x00003724: IN Detect
Vref caps: HIZ 50 GRD 80 100
Pin Default 0x03a11020: [Jack] Mic at Ext Left
Conn = 1/8, Color = Black
DefAssociation = 0x2, Sequence = 0x0
Pin-ctls: 0x24: IN VREF_80
Unsolicited: tag=04, enabled=1
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Node 0x1b [Pin Complex] wcaps 0x40058f: Stereo Amp-In Amp-Out
Amp-In caps: ofs=0x00, nsteps=0x03, stepsize=0x27, mute=0
Amp-In vals: [0x00 0x00]
Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-Out vals: [0x80 0x80]
Pincap 0x0000373c: IN OUT HP Detect
Vref caps: HIZ 50 GRD 80 100
Pin Default 0x411111f0: [N/A] Speaker at Ext Rear
Conn = 1/8, Color = Black
DefAssociation = 0xf, Sequence = 0x0
Misc = NO_PRESENCE
Pin-ctls: 0x20: IN VREF_HIZ
Unsolicited: tag=00, enabled=0
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Connection: 2
0x0c* 0x0d
Node 0x1c [Vendor Defined Widget] wcaps 0xf00000: Mono
Node 0x1d [Pin Complex] wcaps 0x400400: Mono
Pincap 0x00000020: IN
Pin Default 0x40738105: [N/A] Modem Hand at Ext N/A
Conn = ATAPI, Color = Purple
DefAssociation = 0x0, Sequence = 0x5
Misc = NO_PRESENCE
Pin-ctls: 0x20: IN
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Node 0x1e [Pin Complex] wcaps 0x400781: Stereo Digital
Pincap 0x00000014: OUT Detect
Pin Default 0x411111f0: [N/A] Speaker at Ext Rear
Conn = 1/8, Color = Black
DefAssociation = 0xf, Sequence = 0x0
Misc = NO_PRESENCE
Pin-ctls: 0x40: OUT
Unsolicited: tag=00, enabled=0
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Connection: 1
0x06
Node 0x1f [Vendor Defined Widget] wcaps 0xf00000: Mono
Node 0x20 [Vendor Defined Widget] wcaps 0xf00040: Mono
Processing caps: benign=0, ncoeff=90
Node 0x21 [Vendor Defined Widget] wcaps 0xf00000: Mono
Node 0x22 [Audio Selector] wcaps 0x300101: Stereo
Connection: 8
0x18 0x19 0x1a 0x1b 0x1d 0x0b 0x12* 0x13
Node 0x23 [Audio Selector] wcaps 0x300101: Stereo
Connection: 6
0x18* 0x19 0x1a 0x1b 0x1d 0x0b
Node 0x24 [Audio Selector] wcaps 0x300101: Stereo
Connection: 2
0x12* 0x13
Codec: Intel Skylake HDMI
Address: 2
AFG Function Id: 0x1 (unsol 0)
Vendor Id: 0x80862809
Subsystem Id: 0x80860101
Revision Id: 0x100000
No Modem Function Group found
Default PCM:
rates [0x0]:
bits [0x0]:
formats [0x0]:
Default Amp-In caps: N/A
Default Amp-Out caps: N/A
State of AFG node 0x01:
Power states: D0 D3 CLKSTOP EPSS
Power: setting=D0, actual=D0, Clock-stop-OK
GPIO: io=0, o=0, i=0, unsolicited=0, wake=0
Node 0x02 [Audio Output] wcaps 0x6611: 8-Channels Digital
Converter: stream=0, channel=0
Digital: Enabled KAE
Digital category: 0x0
IEC Coding Type: 0x0
PCM:
rates [0x7f0]: 32000 44100 48000 88200 96000 176400 192000
bits [0x1a]: 16 24 32
formats [0x5]: PCM AC3
Power states: D0 D3 EPSS
Power: setting=D0, actual=D0
Node 0x03 [Audio Output] wcaps 0x6611: 8-Channels Digital
Converter: stream=0, channel=0
Digital: Enabled KAE
Digital category: 0x0
IEC Coding Type: 0x0
PCM:
rates [0x7f0]: 32000 44100 48000 88200 96000 176400 192000
bits [0x1a]: 16 24 32
formats [0x5]: PCM AC3
Power states: D0 D3 EPSS
Power: setting=D0, actual=D0
Node 0x04 [Audio Output] wcaps 0x6611: 8-Channels Digital
Converter: stream=0, channel=0
Digital: Enabled KAE
Digital category: 0x0
IEC Coding Type: 0x0
PCM:
rates [0x7f0]: 32000 44100 48000 88200 96000 176400 192000
bits [0x1a]: 16 24 32
formats [0x5]: PCM AC3
Power states: D0 D3 EPSS
Power: setting=D0, actual=D0
Node 0x05 [Pin Complex] wcaps 0x40778d: 8-Channels Digital Amp-Out CP
Control: name="IEC958 Playback Con Mask", index=0, device=0
Control: name="IEC958 Playback Pro Mask", index=0, device=0
Control: name="IEC958 Playback Default", index=0, device=0
Control: name="IEC958 Playback Switch", index=0, device=0
Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-Out vals: [0x00 0x00]
Pincap 0x0b000094: OUT Detect HBR HDMI DP
Pin Default 0x18560010: [Jack] Digital Out at Int HDMI
Conn = Digital, Color = Unknown
DefAssociation = 0x1, Sequence = 0x0
Pin-ctls: 0x00:
Unsolicited: tag=00, enabled=0
Power states: D0 D3 EPSS
Power: setting=D0, actual=D0
Devices: 0
Connection: 0
In-driver Connection: 3
0x02 0x03 0x04
Node 0x06 [Pin Complex] wcaps 0x40778d: 8-Channels Digital Amp-Out CP
Control: name="IEC958 Playback Con Mask", index=1, device=0
Control: name="IEC958 Playback Pro Mask", index=1, device=0
Control: name="IEC958 Playback Default", index=1, device=0
Control: name="IEC958 Playback Switch", index=1, device=0
Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-Out vals: [0x00 0x00]
Pincap 0x0b000094: OUT Detect HBR HDMI DP
Pin Default 0x18560010: [Jack] Digital Out at Int HDMI
Conn = Digital, Color = Unknown
DefAssociation = 0x1, Sequence = 0x0
Pin-ctls: 0x00:
Unsolicited: tag=00, enabled=0
Power states: D0 D3 EPSS
Power: setting=D0, actual=D0
Devices: 0
Connection: 0
In-driver Connection: 3
0x02 0x03 0x04
Node 0x07 [Pin Complex] wcaps 0x40778d: 8-Channels Digital Amp-Out CP
Control: name="IEC958 Playback Con Mask", index=2, device=0
Control: name="IEC958 Playback Pro Mask", index=2, device=0
Control: name="IEC958 Playback Default", index=2, device=0
Control: name="IEC958 Playback Switch", index=2, device=0
Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-Out vals: [0x00 0x00]
Pincap 0x0b000094: OUT Detect HBR HDMI DP
Pin Default 0x18560010: [Jack] Digital Out at Int HDMI
Conn = Digital, Color = Unknown
DefAssociation = 0x1, Sequence = 0x0
Pin-ctls: 0x00:
Unsolicited: tag=00, enabled=0
Power states: D0 D3 EPSS
Power: setting=D0, actual=D0
Devices: 0
Connection: 0
In-driver Connection: 3
0x02 0x03 0x04
Node 0x08 [Vendor Defined Widget] wcaps 0xf00000: Mono
Edit 2:
I have more information about amixer, with and without the microphone plugged in as asked in comment, with these commands:
cat /proc/asound/card0/codec#0 > /tmp/with_mic.codec0.dump
amixer -c0 contents > /tmp/with_mic.contents.dump
# unplug the microphone
cat /proc/asound/card0/codec#0 > /tmp/without_mic.codec0.dump
amixer -c0 contents > /tmp/without_mic.contents.dump
Now if I do a diff on the codec0 files, I find as guessed by @dirkt that Node 0x22 switch from 0x12* to 0x1a.
Node 0x22 [Audio Selector] wcaps 0x300101: Stereo
Connection: 8
- 0x18 0x19 0x1a* 0x1b 0x1d 0x0b 0x12 0x13
+ 0x18 0x19 0x1a 0x1b 0x1d 0x0b 0x12* 0x13
Now I find the only Auto-Mute Mode control, and disabled it.
$ amixer -c0 cget numid=11
numid=11,iface=MIXER,name='Auto-Mute Mode'
; type=ENUMERATED,access=rw------,values=1,items=2
; Item #0 'Disabled'
; Item #1 'Enabled'
: values=1
$ amixer -c0 cset numid=11 0
numid=11,iface=MIXER,name='Auto-Mute Mode'
; type=ENUMERATED,access=rw------,values=1,items=2
; Item #0 'Disabled'
; Item #1 'Enabled'
: values=0
I reproduce the dump with and without the microphone plugged in, but I still have in the difference the switch on the Node 22.
alsa pulseaudio jack
asked Mar 6 '17 at 22:58
aRkadeFRaRkadeFR
1457
bumped to the homepage by Community♦ 2 days ago
This question has answers that may be good or bad; the system has marked it active so that they can be reviewed.
As you run Pulseaudio, try to change Pulseaudio settings, not ALSA settings. In thepavucontrolInput tab, are there Port settings for both the built-in mic and the headset mic? Can you switch?
– dirkt
Mar 7 '17 at 7:06
Ok, got it for Pulseaudio. I can't find anything in pavucontrol in the Input tab. There's only "Built-in Audio Analog Stereo" and the "Monitor of Built-in Audio Analog Stereo" in the Input Devices, and I can choose the port "Internal Microphone (unplugged)", "Microphone (plugged in)" and "Dock Microphone (unplugged)", but either choice is the Jack Microphone.
– aRkadeFR
Mar 7 '17 at 21:08
The interesting point is "unplugged" for the internal mic. When you unplug the jack mic, does that change? Does the internal mic work at all? Intel HDA normally works out of the box, but if your laptop does something funny, you can inspect the codec nodes withcat /proc/asound/card*/codec#*(do both with jack mic unplugged and plugged, observer changes, too). This will need some amount of time to work through, though.
– dirkt
Mar 8 '17 at 7:21
When I unplugged the Jack microphone, the internal microphone works perfectly. And I have in the Input Devices pannel the three choices: "Internal Microphone", "Microphone (unplugged)", "Dock Microphone (unplugged)". So it's like there's a switch between "Internal Microphone" and "Microphone" depending I have the Jack microphone plugged in or not. I edit the question with the output ofcat /proc/asound/card*/codec#*. Thanks
– aRkadeFR
Mar 8 '17 at 9:25
add a comment |
I have laptops running Debian stretch / pulseaudio version 10.0-1 on which I'd like to choose the internal microphone over the mic jack.
When I plug my headphone which includes a microphone through the jack, only the microphone of the headset works and I don't find a way to switch to the built-in one.
$ amixer -c0 controls | grep -i mic
numid=16,iface=CARD,name='Internal Mic Phantom Jack'
numid=15,iface=CARD,name='Mic Jack'
numid=11,iface=MIXER,name='Mic Boost Volume'
numid=7,iface=MIXER,name='Mic Playback Switch'
numid=6,iface=MIXER,name='Mic Playback Volume'
numid=12,iface=MIXER,name='Internal Mic Boost Volume'
My sound card is an HDA Intel PCH on all my laptops.
I tried to disable the iface=CARD numid=15 but I get a Operation not permitted:
$ amixer -c0 cset numid=15 off
amixer: Control hw:0 element write error: Operation not permitted
EDIT:
As suggested in comment, I searched in pavucontrol and pulseaudio settings but can't find anything that solve my problem.
EDIT 2:
In order to have further information on the codecs, I paste the output of the cat /proc/asound/card*/codec#* command:
Codec: Realtek ALC293
Address: 0
AFG Function Id: 0x1 (unsol 1)
Vendor Id: 0x10ec0293
Subsystem Id: 0x17aa504b
Revision Id: 0x100003
No Modem Function Group found
Default PCM:
rates [0x5f0]: 32000 44100 48000 88200 96000 192000
bits [0xe]: 16 20 24
formats [0x1]: PCM
Default Amp-In caps: N/A
Default Amp-Out caps: N/A
State of AFG node 0x01:
Power states: D0 D1 D2 D3 D3cold CLKSTOP EPSS
Power: setting=D0, actual=D0
GPIO: io=5, o=0, i=0, unsolicited=1, wake=0
IO[0]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0
IO[1]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0
IO[2]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0
IO[3]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0
IO[4]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0
Node 0x02 [Audio Output] wcaps 0x41d: Stereo Amp-Out
Control: name="Speaker Playback Volume", index=0, device=0
ControlAmp: chs=3, dir=Out, idx=0, ofs=0
Device: name="ALC293 Analog", type="Audio", device=0
Amp-Out caps: ofs=0x57, nsteps=0x57, stepsize=0x02, mute=0
Amp-Out vals: [0x2b 0x2b]
Converter: stream=1, channel=0
PCM:
rates [0x560]: 44100 48000 96000 192000
bits [0xe]: 16 20 24
formats [0x1]: PCM
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Node 0x03 [Audio Output] wcaps 0x41d: Stereo Amp-Out
Control: name="Headphone Playback Volume", index=0, device=0
ControlAmp: chs=3, dir=Out, idx=0, ofs=0
Amp-Out caps: ofs=0x57, nsteps=0x57, stepsize=0x02, mute=0
Amp-Out vals: [0x00 0x00]
Converter: stream=1, channel=0
PCM:
rates [0x560]: 44100 48000 96000 192000
bits [0xe]: 16 20 24
formats [0x1]: PCM
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Node 0x04 [Vendor Defined Widget] wcaps 0xf00000: Mono
Node 0x05 [Vendor Defined Widget] wcaps 0xf00000: Mono
Node 0x06 [Audio Output] wcaps 0x611: Stereo Digital
Converter: stream=0, channel=0
Digital:
Digital category: 0x0
IEC Coding Type: 0x0
PCM:
rates [0x5f0]: 32000 44100 48000 88200 96000 192000
bits [0xe]: 16 20 24
formats [0x1]: PCM
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Node 0x07 [Audio Input] wcaps 0x10051b: Stereo Amp-In
Amp-In caps: ofs=0x17, nsteps=0x3f, stepsize=0x02, mute=1
Amp-In vals: [0x97 0x97]
Converter: stream=0, channel=0
SDI-Select: 0
PCM:
rates [0x560]: 44100 48000 96000 192000
bits [0xe]: 16 20 24
formats [0x1]: PCM
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Connection: 1
0x24
Node 0x08 [Audio Input] wcaps 0x10051b: Stereo Amp-In
Amp-In caps: ofs=0x17, nsteps=0x3f, stepsize=0x02, mute=1
Amp-In vals: [0x97 0x97]
Converter: stream=0, channel=0
SDI-Select: 0
PCM:
rates [0x560]: 44100 48000 96000 192000
bits [0xe]: 16 20 24
formats [0x1]: PCM
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Connection: 1
0x23
Node 0x09 [Audio Input] wcaps 0x10051b: Stereo Amp-In
Control: name="Capture Volume", index=0, device=0
ControlAmp: chs=3, dir=In, idx=0, ofs=0
Control: name="Capture Switch", index=0, device=0
ControlAmp: chs=3, dir=In, idx=0, ofs=0
Device: name="ALC293 Analog", type="Audio", device=0
Amp-In caps: ofs=0x17, nsteps=0x3f, stepsize=0x02, mute=1
Amp-In vals: [0x3e 0x3e]
Converter: stream=1, channel=0
SDI-Select: 0
PCM:
rates [0x560]: 44100 48000 96000 192000
bits [0xe]: 16 20 24
formats [0x1]: PCM
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Connection: 1
0x22
Node 0x0a [Vendor Defined Widget] wcaps 0xf00000: Mono
Node 0x0b [Audio Mixer] wcaps 0x20010b: Stereo Amp-In
Control: name="Dock Mic Playback Volume", index=0, device=0
ControlAmp: chs=3, dir=In, idx=1, ofs=0
Control: name="Dock Mic Playback Switch", index=0, device=0
ControlAmp: chs=3, dir=In, idx=1, ofs=0
Control: name="Mic Playback Volume", index=0, device=0
ControlAmp: chs=3, dir=In, idx=2, ofs=0
Control: name="Mic Playback Switch", index=0, device=0
ControlAmp: chs=3, dir=In, idx=2, ofs=0
Control: name="Beep Playback Volume", index=0, device=0
ControlAmp: chs=3, dir=In, idx=4, ofs=0
Control: name="Beep Playback Switch", index=0, device=0
ControlAmp: chs=3, dir=In, idx=4, ofs=0
Amp-In caps: ofs=0x17, nsteps=0x1f, stepsize=0x05, mute=1
Amp-In vals: [0x80 0x80] [0x00 0x00] [0x16 0x16] [0x80 0x80] [0x80 0x80]
Connection: 5
0x18 0x19 0x1a 0x1b 0x1d
Node 0x0c [Audio Mixer] wcaps 0x20010b: Stereo Amp-In
Amp-In caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-In vals: [0x00 0x00] [0x80 0x80]
Connection: 2
0x02 0x0b
Node 0x0d [Audio Mixer] wcaps 0x20010b: Stereo Amp-In
Amp-In caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-In vals: [0x00 0x00] [0x80 0x80]
Connection: 2
0x03 0x0b
Node 0x0e [Vendor Defined Widget] wcaps 0xf00000: Mono
Node 0x0f [Vendor Defined Widget] wcaps 0xf00000: Mono
Node 0x10 [Vendor Defined Widget] wcaps 0xf00000: Mono
Node 0x11 [Vendor Defined Widget] wcaps 0xf00000: Mono
Node 0x12 [Pin Complex] wcaps 0x40040b: Stereo Amp-In
Control: name="Internal Mic Boost Volume", index=0, device=0
ControlAmp: chs=3, dir=In, idx=0, ofs=0
Amp-In caps: ofs=0x00, nsteps=0x03, stepsize=0x27, mute=0
Amp-In vals: [0x00 0x00]
Pincap 0x00000020: IN
Pin Default 0x90a60130: [Fixed] Mic at Int N/A
Conn = Digital, Color = Unknown
DefAssociation = 0x3, Sequence = 0x0
Misc = NO_PRESENCE
Pin-ctls: 0x20: IN
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Node 0x13 [Pin Complex] wcaps 0x40040b: Stereo Amp-In
Amp-In caps: ofs=0x00, nsteps=0x03, stepsize=0x27, mute=0
Amp-In vals: [0x00 0x00]
Pincap 0x00000020: IN
Pin Default 0x40000000: [N/A] Line Out at Ext N/A
Conn = Unknown, Color = Unknown
DefAssociation = 0x0, Sequence = 0x0
Pin-ctls: 0x00:
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Node 0x14 [Pin Complex] wcaps 0x40058d: Stereo Amp-Out
Control: name="Speaker Playback Switch", index=0, device=0
ControlAmp: chs=3, dir=Out, idx=0, ofs=0
Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-Out vals: [0x80 0x80]
Pincap 0x00010010: OUT EAPD
EAPD 0x2: EAPD
Pin Default 0x90170110: [Fixed] Speaker at Int N/A
Conn = Analog, Color = Unknown
DefAssociation = 0x1, Sequence = 0x0
Misc = NO_PRESENCE
Pin-ctls: 0x40: OUT
Unsolicited: tag=00, enabled=0
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Connection: 1
0x0c
Node 0x15 [Pin Complex] wcaps 0x40058d: Stereo Amp-Out
Control: name="Headphone Playback Switch", index=1, device=0
ControlAmp: chs=3, dir=Out, idx=0, ofs=0
Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-Out vals: [0x00 0x00]
Pincap 0x0001001c: OUT HP EAPD Detect
EAPD 0x2: EAPD
Pin Default 0x03211040: [Jack] HP Out at Ext Left
Conn = 1/8, Color = Black
DefAssociation = 0x4, Sequence = 0x0
Pin-ctls: 0xc0: OUT HP
Unsolicited: tag=02, enabled=1
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Connection: 2
0x0c 0x0d*
Node 0x16 [Pin Complex] wcaps 0x40058d: Stereo Amp-Out
Control: name="Headphone Playback Switch", index=0, device=0
ControlAmp: chs=3, dir=Out, idx=0, ofs=0
Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-Out vals: [0x80 0x80]
Pincap 0x0001001c: OUT HP EAPD Detect
EAPD 0x2: EAPD
Pin Default 0x411111f0: [N/A] Speaker at Ext Rear
Conn = 1/8, Color = Black
DefAssociation = 0xf, Sequence = 0x0
Misc = NO_PRESENCE
Pin-ctls: 0xc0: OUT HP
Unsolicited: tag=01, enabled=1
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Connection: 2
0x0c 0x0d*
Node 0x17 [Vendor Defined Widget] wcaps 0xf00000: Mono
Node 0x18 [Pin Complex] wcaps 0x40058f: Stereo Amp-In Amp-Out
Amp-In caps: ofs=0x00, nsteps=0x03, stepsize=0x27, mute=0
Amp-In vals: [0x00 0x00]
Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-Out vals: [0x80 0x80]
Pincap 0x0000373c: IN OUT HP Detect
Vref caps: HIZ 50 GRD 80 100
Pin Default 0x411111f0: [N/A] Speaker at Ext Rear
Conn = 1/8, Color = Black
DefAssociation = 0xf, Sequence = 0x0
Misc = NO_PRESENCE
Pin-ctls: 0x00: VREF_HIZ
Unsolicited: tag=00, enabled=0
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Connection: 2
0x0c* 0x0d
Node 0x19 [Pin Complex] wcaps 0x40048b: Stereo Amp-In
Control: name="Dock Mic Boost Volume", index=0, device=0
ControlAmp: chs=3, dir=In, idx=0, ofs=0
Amp-In caps: ofs=0x00, nsteps=0x03, stepsize=0x27, mute=0
Amp-In vals: [0x00 0x00]
Pincap 0x00000024: IN Detect
Pin Default 0x411111f0: [N/A] Speaker at Ext Rear
Conn = 1/8, Color = Black
DefAssociation = 0xf, Sequence = 0x0
Misc = NO_PRESENCE
Pin-ctls: 0x20: IN
Unsolicited: tag=03, enabled=1
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Node 0x1a [Pin Complex] wcaps 0x40048b: Stereo Amp-In
Control: name="Mic Boost Volume", index=0, device=0
ControlAmp: chs=3, dir=In, idx=0, ofs=0
Amp-In caps: ofs=0x00, nsteps=0x03, stepsize=0x27, mute=0
Amp-In vals: [0x00 0x00]
Pincap 0x00003724: IN Detect
Vref caps: HIZ 50 GRD 80 100
Pin Default 0x03a11020: [Jack] Mic at Ext Left
Conn = 1/8, Color = Black
DefAssociation = 0x2, Sequence = 0x0
Pin-ctls: 0x24: IN VREF_80
Unsolicited: tag=04, enabled=1
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Node 0x1b [Pin Complex] wcaps 0x40058f: Stereo Amp-In Amp-Out
Amp-In caps: ofs=0x00, nsteps=0x03, stepsize=0x27, mute=0
Amp-In vals: [0x00 0x00]
Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-Out vals: [0x80 0x80]
Pincap 0x0000373c: IN OUT HP Detect
Vref caps: HIZ 50 GRD 80 100
Pin Default 0x411111f0: [N/A] Speaker at Ext Rear
Conn = 1/8, Color = Black
DefAssociation = 0xf, Sequence = 0x0
Misc = NO_PRESENCE
Pin-ctls: 0x20: IN VREF_HIZ
Unsolicited: tag=00, enabled=0
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Connection: 2
0x0c* 0x0d
Node 0x1c [Vendor Defined Widget] wcaps 0xf00000: Mono
Node 0x1d [Pin Complex] wcaps 0x400400: Mono
Pincap 0x00000020: IN
Pin Default 0x40738105: [N/A] Modem Hand at Ext N/A
Conn = ATAPI, Color = Purple
DefAssociation = 0x0, Sequence = 0x5
Misc = NO_PRESENCE
Pin-ctls: 0x20: IN
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Node 0x1e [Pin Complex] wcaps 0x400781: Stereo Digital
Pincap 0x00000014: OUT Detect
Pin Default 0x411111f0: [N/A] Speaker at Ext Rear
Conn = 1/8, Color = Black
DefAssociation = 0xf, Sequence = 0x0
Misc = NO_PRESENCE
Pin-ctls: 0x40: OUT
Unsolicited: tag=00, enabled=0
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Connection: 1
0x06
Node 0x1f [Vendor Defined Widget] wcaps 0xf00000: Mono
Node 0x20 [Vendor Defined Widget] wcaps 0xf00040: Mono
Processing caps: benign=0, ncoeff=90
Node 0x21 [Vendor Defined Widget] wcaps 0xf00000: Mono
Node 0x22 [Audio Selector] wcaps 0x300101: Stereo
Connection: 8
0x18 0x19 0x1a 0x1b 0x1d 0x0b 0x12* 0x13
Node 0x23 [Audio Selector] wcaps 0x300101: Stereo
Connection: 6
0x18* 0x19 0x1a 0x1b 0x1d 0x0b
Node 0x24 [Audio Selector] wcaps 0x300101: Stereo
Connection: 2
0x12* 0x13
Codec: Intel Skylake HDMI
Address: 2
AFG Function Id: 0x1 (unsol 0)
Vendor Id: 0x80862809
Subsystem Id: 0x80860101
Revision Id: 0x100000
No Modem Function Group found
Default PCM:
rates [0x0]:
bits [0x0]:
formats [0x0]:
Default Amp-In caps: N/A
Default Amp-Out caps: N/A
State of AFG node 0x01:
Power states: D0 D3 CLKSTOP EPSS
Power: setting=D0, actual=D0, Clock-stop-OK
GPIO: io=0, o=0, i=0, unsolicited=0, wake=0
Node 0x02 [Audio Output] wcaps 0x6611: 8-Channels Digital
Converter: stream=0, channel=0
Digital: Enabled KAE
Digital category: 0x0
IEC Coding Type: 0x0
PCM:
rates [0x7f0]: 32000 44100 48000 88200 96000 176400 192000
bits [0x1a]: 16 24 32
formats [0x5]: PCM AC3
Power states: D0 D3 EPSS
Power: setting=D0, actual=D0
Node 0x03 [Audio Output] wcaps 0x6611: 8-Channels Digital
Converter: stream=0, channel=0
Digital: Enabled KAE
Digital category: 0x0
IEC Coding Type: 0x0
PCM:
rates [0x7f0]: 32000 44100 48000 88200 96000 176400 192000
bits [0x1a]: 16 24 32
formats [0x5]: PCM AC3
Power states: D0 D3 EPSS
Power: setting=D0, actual=D0
Node 0x04 [Audio Output] wcaps 0x6611: 8-Channels Digital
Converter: stream=0, channel=0
Digital: Enabled KAE
Digital category: 0x0
IEC Coding Type: 0x0
PCM:
rates [0x7f0]: 32000 44100 48000 88200 96000 176400 192000
bits [0x1a]: 16 24 32
formats [0x5]: PCM AC3
Power states: D0 D3 EPSS
Power: setting=D0, actual=D0
Node 0x05 [Pin Complex] wcaps 0x40778d: 8-Channels Digital Amp-Out CP
Control: name="IEC958 Playback Con Mask", index=0, device=0
Control: name="IEC958 Playback Pro Mask", index=0, device=0
Control: name="IEC958 Playback Default", index=0, device=0
Control: name="IEC958 Playback Switch", index=0, device=0
Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-Out vals: [0x00 0x00]
Pincap 0x0b000094: OUT Detect HBR HDMI DP
Pin Default 0x18560010: [Jack] Digital Out at Int HDMI
Conn = Digital, Color = Unknown
DefAssociation = 0x1, Sequence = 0x0
Pin-ctls: 0x00:
Unsolicited: tag=00, enabled=0
Power states: D0 D3 EPSS
Power: setting=D0, actual=D0
Devices: 0
Connection: 0
In-driver Connection: 3
0x02 0x03 0x04
Node 0x06 [Pin Complex] wcaps 0x40778d: 8-Channels Digital Amp-Out CP
Control: name="IEC958 Playback Con Mask", index=1, device=0
Control: name="IEC958 Playback Pro Mask", index=1, device=0
Control: name="IEC958 Playback Default", index=1, device=0
Control: name="IEC958 Playback Switch", index=1, device=0
Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-Out vals: [0x00 0x00]
Pincap 0x0b000094: OUT Detect HBR HDMI DP
Pin Default 0x18560010: [Jack] Digital Out at Int HDMI
Conn = Digital, Color = Unknown
DefAssociation = 0x1, Sequence = 0x0
Pin-ctls: 0x00:
Unsolicited: tag=00, enabled=0
Power states: D0 D3 EPSS
Power: setting=D0, actual=D0
Devices: 0
Connection: 0
In-driver Connection: 3
0x02 0x03 0x04
Node 0x07 [Pin Complex] wcaps 0x40778d: 8-Channels Digital Amp-Out CP
Control: name="IEC958 Playback Con Mask", index=2, device=0
Control: name="IEC958 Playback Pro Mask", index=2, device=0
Control: name="IEC958 Playback Default", index=2, device=0
Control: name="IEC958 Playback Switch", index=2, device=0
Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-Out vals: [0x00 0x00]
Pincap 0x0b000094: OUT Detect HBR HDMI DP
Pin Default 0x18560010: [Jack] Digital Out at Int HDMI
Conn = Digital, Color = Unknown
DefAssociation = 0x1, Sequence = 0x0
Pin-ctls: 0x00:
Unsolicited: tag=00, enabled=0
Power states: D0 D3 EPSS
Power: setting=D0, actual=D0
Devices: 0
Connection: 0
In-driver Connection: 3
0x02 0x03 0x04
Node 0x08 [Vendor Defined Widget] wcaps 0xf00000: Mono
Edit 2:
I have more information about amixer, with and without the microphone plugged in as asked in comment, with these commands:
cat /proc/asound/card0/codec#0 > /tmp/with_mic.codec0.dump
amixer -c0 contents > /tmp/with_mic.contents.dump
# unplug the microphone
cat /proc/asound/card0/codec#0 > /tmp/without_mic.codec0.dump
amixer -c0 contents > /tmp/without_mic.contents.dump
Now if I do a diff on the codec0 files, I find as guessed by @dirkt that Node 0x22 switch from 0x12* to 0x1a.
Node 0x22 [Audio Selector] wcaps 0x300101: Stereo
Connection: 8
- 0x18 0x19 0x1a* 0x1b 0x1d 0x0b 0x12 0x13
+ 0x18 0x19 0x1a 0x1b 0x1d 0x0b 0x12* 0x13
Now I find the only Auto-Mute Mode control, and disabled it.
$ amixer -c0 cget numid=11
numid=11,iface=MIXER,name='Auto-Mute Mode'
; type=ENUMERATED,access=rw------,values=1,items=2
; Item #0 'Disabled'
; Item #1 'Enabled'
: values=1
$ amixer -c0 cset numid=11 0
numid=11,iface=MIXER,name='Auto-Mute Mode'
; type=ENUMERATED,access=rw------,values=1,items=2
; Item #0 'Disabled'
; Item #1 'Enabled'
: values=0
I reproduce the dump with and without the microphone plugged in, but I still have in the difference the switch on the Node 22.
alsa pulseaudio jack
asked Mar 6 '17 at 22:58
aRkadeFRaRkadeFR
1457
I have laptops running Debian stretch / pulseaudio version 10.0-1 on which I'd like to choose the internal microphone over the mic jack.
When I plug my headphone which includes a microphone through the jack, only the microphone of the headset works and I don't find a way to switch to the built-in one.
$ amixer -c0 controls | grep -i mic
numid=16,iface=CARD,name='Internal Mic Phantom Jack'
numid=15,iface=CARD,name='Mic Jack'
numid=11,iface=MIXER,name='Mic Boost Volume'
numid=7,iface=MIXER,name='Mic Playback Switch'
numid=6,iface=MIXER,name='Mic Playback Volume'
numid=12,iface=MIXER,name='Internal Mic Boost Volume'
My sound card is an HDA Intel PCH on all my laptops.
I tried to disable the iface=CARD numid=15 but I get a Operation not permitted:
$ amixer -c0 cset numid=15 off
amixer: Control hw:0 element write error: Operation not permitted
EDIT:
As suggested in comment, I searched in pavucontrol and pulseaudio settings but can't find anything that solve my problem.
EDIT 2:
In order to have further information on the codecs, I paste the output of the cat /proc/asound/card*/codec#* command:
Codec: Realtek ALC293
Address: 0
AFG Function Id: 0x1 (unsol 1)
Vendor Id: 0x10ec0293
Subsystem Id: 0x17aa504b
Revision Id: 0x100003
No Modem Function Group found
Default PCM:
rates [0x5f0]: 32000 44100 48000 88200 96000 192000
bits [0xe]: 16 20 24
formats [0x1]: PCM
Default Amp-In caps: N/A
Default Amp-Out caps: N/A
State of AFG node 0x01:
Power states: D0 D1 D2 D3 D3cold CLKSTOP EPSS
Power: setting=D0, actual=D0
GPIO: io=5, o=0, i=0, unsolicited=1, wake=0
IO[0]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0
IO[1]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0
IO[2]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0
IO[3]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0
IO[4]: enable=0, dir=0, wake=0, sticky=0, data=0, unsol=0
Node 0x02 [Audio Output] wcaps 0x41d: Stereo Amp-Out
Control: name="Speaker Playback Volume", index=0, device=0
ControlAmp: chs=3, dir=Out, idx=0, ofs=0
Device: name="ALC293 Analog", type="Audio", device=0
Amp-Out caps: ofs=0x57, nsteps=0x57, stepsize=0x02, mute=0
Amp-Out vals: [0x2b 0x2b]
Converter: stream=1, channel=0
PCM:
rates [0x560]: 44100 48000 96000 192000
bits [0xe]: 16 20 24
formats [0x1]: PCM
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Node 0x03 [Audio Output] wcaps 0x41d: Stereo Amp-Out
Control: name="Headphone Playback Volume", index=0, device=0
ControlAmp: chs=3, dir=Out, idx=0, ofs=0
Amp-Out caps: ofs=0x57, nsteps=0x57, stepsize=0x02, mute=0
Amp-Out vals: [0x00 0x00]
Converter: stream=1, channel=0
PCM:
rates [0x560]: 44100 48000 96000 192000
bits [0xe]: 16 20 24
formats [0x1]: PCM
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Node 0x04 [Vendor Defined Widget] wcaps 0xf00000: Mono
Node 0x05 [Vendor Defined Widget] wcaps 0xf00000: Mono
Node 0x06 [Audio Output] wcaps 0x611: Stereo Digital
Converter: stream=0, channel=0
Digital:
Digital category: 0x0
IEC Coding Type: 0x0
PCM:
rates [0x5f0]: 32000 44100 48000 88200 96000 192000
bits [0xe]: 16 20 24
formats [0x1]: PCM
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Node 0x07 [Audio Input] wcaps 0x10051b: Stereo Amp-In
Amp-In caps: ofs=0x17, nsteps=0x3f, stepsize=0x02, mute=1
Amp-In vals: [0x97 0x97]
Converter: stream=0, channel=0
SDI-Select: 0
PCM:
rates [0x560]: 44100 48000 96000 192000
bits [0xe]: 16 20 24
formats [0x1]: PCM
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Connection: 1
0x24
Node 0x08 [Audio Input] wcaps 0x10051b: Stereo Amp-In
Amp-In caps: ofs=0x17, nsteps=0x3f, stepsize=0x02, mute=1
Amp-In vals: [0x97 0x97]
Converter: stream=0, channel=0
SDI-Select: 0
PCM:
rates [0x560]: 44100 48000 96000 192000
bits [0xe]: 16 20 24
formats [0x1]: PCM
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Connection: 1
0x23
Node 0x09 [Audio Input] wcaps 0x10051b: Stereo Amp-In
Control: name="Capture Volume", index=0, device=0
ControlAmp: chs=3, dir=In, idx=0, ofs=0
Control: name="Capture Switch", index=0, device=0
ControlAmp: chs=3, dir=In, idx=0, ofs=0
Device: name="ALC293 Analog", type="Audio", device=0
Amp-In caps: ofs=0x17, nsteps=0x3f, stepsize=0x02, mute=1
Amp-In vals: [0x3e 0x3e]
Converter: stream=1, channel=0
SDI-Select: 0
PCM:
rates [0x560]: 44100 48000 96000 192000
bits [0xe]: 16 20 24
formats [0x1]: PCM
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Connection: 1
0x22
Node 0x0a [Vendor Defined Widget] wcaps 0xf00000: Mono
Node 0x0b [Audio Mixer] wcaps 0x20010b: Stereo Amp-In
Control: name="Dock Mic Playback Volume", index=0, device=0
ControlAmp: chs=3, dir=In, idx=1, ofs=0
Control: name="Dock Mic Playback Switch", index=0, device=0
ControlAmp: chs=3, dir=In, idx=1, ofs=0
Control: name="Mic Playback Volume", index=0, device=0
ControlAmp: chs=3, dir=In, idx=2, ofs=0
Control: name="Mic Playback Switch", index=0, device=0
ControlAmp: chs=3, dir=In, idx=2, ofs=0
Control: name="Beep Playback Volume", index=0, device=0
ControlAmp: chs=3, dir=In, idx=4, ofs=0
Control: name="Beep Playback Switch", index=0, device=0
ControlAmp: chs=3, dir=In, idx=4, ofs=0
Amp-In caps: ofs=0x17, nsteps=0x1f, stepsize=0x05, mute=1
Amp-In vals: [0x80 0x80] [0x00 0x00] [0x16 0x16] [0x80 0x80] [0x80 0x80]
Connection: 5
0x18 0x19 0x1a 0x1b 0x1d
Node 0x0c [Audio Mixer] wcaps 0x20010b: Stereo Amp-In
Amp-In caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-In vals: [0x00 0x00] [0x80 0x80]
Connection: 2
0x02 0x0b
Node 0x0d [Audio Mixer] wcaps 0x20010b: Stereo Amp-In
Amp-In caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-In vals: [0x00 0x00] [0x80 0x80]
Connection: 2
0x03 0x0b
Node 0x0e [Vendor Defined Widget] wcaps 0xf00000: Mono
Node 0x0f [Vendor Defined Widget] wcaps 0xf00000: Mono
Node 0x10 [Vendor Defined Widget] wcaps 0xf00000: Mono
Node 0x11 [Vendor Defined Widget] wcaps 0xf00000: Mono
Node 0x12 [Pin Complex] wcaps 0x40040b: Stereo Amp-In
Control: name="Internal Mic Boost Volume", index=0, device=0
ControlAmp: chs=3, dir=In, idx=0, ofs=0
Amp-In caps: ofs=0x00, nsteps=0x03, stepsize=0x27, mute=0
Amp-In vals: [0x00 0x00]
Pincap 0x00000020: IN
Pin Default 0x90a60130: [Fixed] Mic at Int N/A
Conn = Digital, Color = Unknown
DefAssociation = 0x3, Sequence = 0x0
Misc = NO_PRESENCE
Pin-ctls: 0x20: IN
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Node 0x13 [Pin Complex] wcaps 0x40040b: Stereo Amp-In
Amp-In caps: ofs=0x00, nsteps=0x03, stepsize=0x27, mute=0
Amp-In vals: [0x00 0x00]
Pincap 0x00000020: IN
Pin Default 0x40000000: [N/A] Line Out at Ext N/A
Conn = Unknown, Color = Unknown
DefAssociation = 0x0, Sequence = 0x0
Pin-ctls: 0x00:
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Node 0x14 [Pin Complex] wcaps 0x40058d: Stereo Amp-Out
Control: name="Speaker Playback Switch", index=0, device=0
ControlAmp: chs=3, dir=Out, idx=0, ofs=0
Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-Out vals: [0x80 0x80]
Pincap 0x00010010: OUT EAPD
EAPD 0x2: EAPD
Pin Default 0x90170110: [Fixed] Speaker at Int N/A
Conn = Analog, Color = Unknown
DefAssociation = 0x1, Sequence = 0x0
Misc = NO_PRESENCE
Pin-ctls: 0x40: OUT
Unsolicited: tag=00, enabled=0
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Connection: 1
0x0c
Node 0x15 [Pin Complex] wcaps 0x40058d: Stereo Amp-Out
Control: name="Headphone Playback Switch", index=1, device=0
ControlAmp: chs=3, dir=Out, idx=0, ofs=0
Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-Out vals: [0x00 0x00]
Pincap 0x0001001c: OUT HP EAPD Detect
EAPD 0x2: EAPD
Pin Default 0x03211040: [Jack] HP Out at Ext Left
Conn = 1/8, Color = Black
DefAssociation = 0x4, Sequence = 0x0
Pin-ctls: 0xc0: OUT HP
Unsolicited: tag=02, enabled=1
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Connection: 2
0x0c 0x0d*
Node 0x16 [Pin Complex] wcaps 0x40058d: Stereo Amp-Out
Control: name="Headphone Playback Switch", index=0, device=0
ControlAmp: chs=3, dir=Out, idx=0, ofs=0
Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-Out vals: [0x80 0x80]
Pincap 0x0001001c: OUT HP EAPD Detect
EAPD 0x2: EAPD
Pin Default 0x411111f0: [N/A] Speaker at Ext Rear
Conn = 1/8, Color = Black
DefAssociation = 0xf, Sequence = 0x0
Misc = NO_PRESENCE
Pin-ctls: 0xc0: OUT HP
Unsolicited: tag=01, enabled=1
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Connection: 2
0x0c 0x0d*
Node 0x17 [Vendor Defined Widget] wcaps 0xf00000: Mono
Node 0x18 [Pin Complex] wcaps 0x40058f: Stereo Amp-In Amp-Out
Amp-In caps: ofs=0x00, nsteps=0x03, stepsize=0x27, mute=0
Amp-In vals: [0x00 0x00]
Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-Out vals: [0x80 0x80]
Pincap 0x0000373c: IN OUT HP Detect
Vref caps: HIZ 50 GRD 80 100
Pin Default 0x411111f0: [N/A] Speaker at Ext Rear
Conn = 1/8, Color = Black
DefAssociation = 0xf, Sequence = 0x0
Misc = NO_PRESENCE
Pin-ctls: 0x00: VREF_HIZ
Unsolicited: tag=00, enabled=0
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Connection: 2
0x0c* 0x0d
Node 0x19 [Pin Complex] wcaps 0x40048b: Stereo Amp-In
Control: name="Dock Mic Boost Volume", index=0, device=0
ControlAmp: chs=3, dir=In, idx=0, ofs=0
Amp-In caps: ofs=0x00, nsteps=0x03, stepsize=0x27, mute=0
Amp-In vals: [0x00 0x00]
Pincap 0x00000024: IN Detect
Pin Default 0x411111f0: [N/A] Speaker at Ext Rear
Conn = 1/8, Color = Black
DefAssociation = 0xf, Sequence = 0x0
Misc = NO_PRESENCE
Pin-ctls: 0x20: IN
Unsolicited: tag=03, enabled=1
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Node 0x1a [Pin Complex] wcaps 0x40048b: Stereo Amp-In
Control: name="Mic Boost Volume", index=0, device=0
ControlAmp: chs=3, dir=In, idx=0, ofs=0
Amp-In caps: ofs=0x00, nsteps=0x03, stepsize=0x27, mute=0
Amp-In vals: [0x00 0x00]
Pincap 0x00003724: IN Detect
Vref caps: HIZ 50 GRD 80 100
Pin Default 0x03a11020: [Jack] Mic at Ext Left
Conn = 1/8, Color = Black
DefAssociation = 0x2, Sequence = 0x0
Pin-ctls: 0x24: IN VREF_80
Unsolicited: tag=04, enabled=1
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Node 0x1b [Pin Complex] wcaps 0x40058f: Stereo Amp-In Amp-Out
Amp-In caps: ofs=0x00, nsteps=0x03, stepsize=0x27, mute=0
Amp-In vals: [0x00 0x00]
Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-Out vals: [0x80 0x80]
Pincap 0x0000373c: IN OUT HP Detect
Vref caps: HIZ 50 GRD 80 100
Pin Default 0x411111f0: [N/A] Speaker at Ext Rear
Conn = 1/8, Color = Black
DefAssociation = 0xf, Sequence = 0x0
Misc = NO_PRESENCE
Pin-ctls: 0x20: IN VREF_HIZ
Unsolicited: tag=00, enabled=0
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Connection: 2
0x0c* 0x0d
Node 0x1c [Vendor Defined Widget] wcaps 0xf00000: Mono
Node 0x1d [Pin Complex] wcaps 0x400400: Mono
Pincap 0x00000020: IN
Pin Default 0x40738105: [N/A] Modem Hand at Ext N/A
Conn = ATAPI, Color = Purple
DefAssociation = 0x0, Sequence = 0x5
Misc = NO_PRESENCE
Pin-ctls: 0x20: IN
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Node 0x1e [Pin Complex] wcaps 0x400781: Stereo Digital
Pincap 0x00000014: OUT Detect
Pin Default 0x411111f0: [N/A] Speaker at Ext Rear
Conn = 1/8, Color = Black
DefAssociation = 0xf, Sequence = 0x0
Misc = NO_PRESENCE
Pin-ctls: 0x40: OUT
Unsolicited: tag=00, enabled=0
Power states: D0 D1 D2 D3 EPSS
Power: setting=D0, actual=D0
Connection: 1
0x06
Node 0x1f [Vendor Defined Widget] wcaps 0xf00000: Mono
Node 0x20 [Vendor Defined Widget] wcaps 0xf00040: Mono
Processing caps: benign=0, ncoeff=90
Node 0x21 [Vendor Defined Widget] wcaps 0xf00000: Mono
Node 0x22 [Audio Selector] wcaps 0x300101: Stereo
Connection: 8
0x18 0x19 0x1a 0x1b 0x1d 0x0b 0x12* 0x13
Node 0x23 [Audio Selector] wcaps 0x300101: Stereo
Connection: 6
0x18* 0x19 0x1a 0x1b 0x1d 0x0b
Node 0x24 [Audio Selector] wcaps 0x300101: Stereo
Connection: 2
0x12* 0x13
Codec: Intel Skylake HDMI
Address: 2
AFG Function Id: 0x1 (unsol 0)
Vendor Id: 0x80862809
Subsystem Id: 0x80860101
Revision Id: 0x100000
No Modem Function Group found
Default PCM:
rates [0x0]:
bits [0x0]:
formats [0x0]:
Default Amp-In caps: N/A
Default Amp-Out caps: N/A
State of AFG node 0x01:
Power states: D0 D3 CLKSTOP EPSS
Power: setting=D0, actual=D0, Clock-stop-OK
GPIO: io=0, o=0, i=0, unsolicited=0, wake=0
Node 0x02 [Audio Output] wcaps 0x6611: 8-Channels Digital
Converter: stream=0, channel=0
Digital: Enabled KAE
Digital category: 0x0
IEC Coding Type: 0x0
PCM:
rates [0x7f0]: 32000 44100 48000 88200 96000 176400 192000
bits [0x1a]: 16 24 32
formats [0x5]: PCM AC3
Power states: D0 D3 EPSS
Power: setting=D0, actual=D0
Node 0x03 [Audio Output] wcaps 0x6611: 8-Channels Digital
Converter: stream=0, channel=0
Digital: Enabled KAE
Digital category: 0x0
IEC Coding Type: 0x0
PCM:
rates [0x7f0]: 32000 44100 48000 88200 96000 176400 192000
bits [0x1a]: 16 24 32
formats [0x5]: PCM AC3
Power states: D0 D3 EPSS
Power: setting=D0, actual=D0
Node 0x04 [Audio Output] wcaps 0x6611: 8-Channels Digital
Converter: stream=0, channel=0
Digital: Enabled KAE
Digital category: 0x0
IEC Coding Type: 0x0
PCM:
rates [0x7f0]: 32000 44100 48000 88200 96000 176400 192000
bits [0x1a]: 16 24 32
formats [0x5]: PCM AC3
Power states: D0 D3 EPSS
Power: setting=D0, actual=D0
Node 0x05 [Pin Complex] wcaps 0x40778d: 8-Channels Digital Amp-Out CP
Control: name="IEC958 Playback Con Mask", index=0, device=0
Control: name="IEC958 Playback Pro Mask", index=0, device=0
Control: name="IEC958 Playback Default", index=0, device=0
Control: name="IEC958 Playback Switch", index=0, device=0
Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-Out vals: [0x00 0x00]
Pincap 0x0b000094: OUT Detect HBR HDMI DP
Pin Default 0x18560010: [Jack] Digital Out at Int HDMI
Conn = Digital, Color = Unknown
DefAssociation = 0x1, Sequence = 0x0
Pin-ctls: 0x00:
Unsolicited: tag=00, enabled=0
Power states: D0 D3 EPSS
Power: setting=D0, actual=D0
Devices: 0
Connection: 0
In-driver Connection: 3
0x02 0x03 0x04
Node 0x06 [Pin Complex] wcaps 0x40778d: 8-Channels Digital Amp-Out CP
Control: name="IEC958 Playback Con Mask", index=1, device=0
Control: name="IEC958 Playback Pro Mask", index=1, device=0
Control: name="IEC958 Playback Default", index=1, device=0
Control: name="IEC958 Playback Switch", index=1, device=0
Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-Out vals: [0x00 0x00]
Pincap 0x0b000094: OUT Detect HBR HDMI DP
Pin Default 0x18560010: [Jack] Digital Out at Int HDMI
Conn = Digital, Color = Unknown
DefAssociation = 0x1, Sequence = 0x0
Pin-ctls: 0x00:
Unsolicited: tag=00, enabled=0
Power states: D0 D3 EPSS
Power: setting=D0, actual=D0
Devices: 0
Connection: 0
In-driver Connection: 3
0x02 0x03 0x04
Node 0x07 [Pin Complex] wcaps 0x40778d: 8-Channels Digital Amp-Out CP
Control: name="IEC958 Playback Con Mask", index=2, device=0
Control: name="IEC958 Playback Pro Mask", index=2, device=0
Control: name="IEC958 Playback Default", index=2, device=0
Control: name="IEC958 Playback Switch", index=2, device=0
Amp-Out caps: ofs=0x00, nsteps=0x00, stepsize=0x00, mute=1
Amp-Out vals: [0x00 0x00]
Pincap 0x0b000094: OUT Detect HBR HDMI DP
Pin Default 0x18560010: [Jack] Digital Out at Int HDMI
Conn = Digital, Color = Unknown
DefAssociation = 0x1, Sequence = 0x0
Pin-ctls: 0x00:
Unsolicited: tag=00, enabled=0
Power states: D0 D3 EPSS
Power: setting=D0, actual=D0
Devices: 0
Connection: 0
In-driver Connection: 3
0x02 0x03 0x04
Node 0x08 [Vendor Defined Widget] wcaps 0xf00000: Mono
Edit 2:
I have more information about amixer, with and without the microphone plugged in as asked in comment, with these commands:
cat /proc/asound/card0/codec#0 > /tmp/with_mic.codec0.dump
amixer -c0 contents > /tmp/with_mic.contents.dump
# unplug the microphone
cat /proc/asound/card0/codec#0 > /tmp/without_mic.codec0.dump
amixer -c0 contents > /tmp/without_mic.contents.dump
Now if I do a diff on the codec0 files, I find as guessed by @dirkt that Node 0x22 switch from 0x12* to 0x1a.
Node 0x22 [Audio Selector] wcaps 0x300101: Stereo
Connection: 8
- 0x18 0x19 0x1a* 0x1b 0x1d 0x0b 0x12 0x13
+ 0x18 0x19 0x1a 0x1b 0x1d 0x0b 0x12* 0x13
Now I find the only Auto-Mute Mode control, and disabled it.
$ amixer -c0 cget numid=11
numid=11,iface=MIXER,name='Auto-Mute Mode'
; type=ENUMERATED,access=rw------,values=1,items=2
; Item #0 'Disabled'
; Item #1 'Enabled'
: values=1
$ amixer -c0 cset numid=11 0
numid=11,iface=MIXER,name='Auto-Mute Mode'
; type=ENUMERATED,access=rw------,values=1,items=2
; Item #0 'Disabled'
; Item #1 'Enabled'
: values=0
I reproduce the dump with and without the microphone plugged in, but I still have in the difference the switch on the Node 22.
alsa pulseaudio jack
alsa pulseaudio jack
asked Mar 6 '17 at 22:58
aRkadeFRaRkadeFR
1457
asked Mar 6 '17 at 22:58
aRkadeFRaRkadeFR
1457
edited Mar 10 '17 at 12:44
aRkadeFR
asked Mar 6 '17 at 22:58
aRkadeFRaRkadeFR
1457
asked Mar 6 '17 at 22:58
aRkadeFRaRkadeFR
1457
asked Mar 6 '17 at 22:58
aRkadeFRaRkadeFR
1457
1457
bumped to the homepage by Community♦ 2 days ago
This question has answers that may be good or bad; the system has marked it active so that they can be reviewed.
bumped to the homepage by Community♦ 2 days ago
This question has answers that may be good or bad; the system has marked it active so that they can be reviewed.
As you run Pulseaudio, try to change Pulseaudio settings, not ALSA settings. In thepavucontrolInput tab, are there Port settings for both the built-in mic and the headset mic? Can you switch?
– dirkt
Mar 7 '17 at 7:06
Ok, got it for Pulseaudio. I can't find anything in pavucontrol in the Input tab. There's only "Built-in Audio Analog Stereo" and the "Monitor of Built-in Audio Analog Stereo" in the Input Devices, and I can choose the port "Internal Microphone (unplugged)", "Microphone (plugged in)" and "Dock Microphone (unplugged)", but either choice is the Jack Microphone.
– aRkadeFR
Mar 7 '17 at 21:08
The interesting point is "unplugged" for the internal mic. When you unplug the jack mic, does that change? Does the internal mic work at all? Intel HDA normally works out of the box, but if your laptop does something funny, you can inspect the codec nodes withcat /proc/asound/card*/codec#*(do both with jack mic unplugged and plugged, observer changes, too). This will need some amount of time to work through, though.
– dirkt
Mar 8 '17 at 7:21
When I unplugged the Jack microphone, the internal microphone works perfectly. And I have in the Input Devices pannel the three choices: "Internal Microphone", "Microphone (unplugged)", "Dock Microphone (unplugged)". So it's like there's a switch between "Internal Microphone" and "Microphone" depending I have the Jack microphone plugged in or not. I edit the question with the output ofcat /proc/asound/card*/codec#*. Thanks
– aRkadeFR
Mar 8 '17 at 9:25
add a comment |
As you run Pulseaudio, try to change Pulseaudio settings, not ALSA settings. In thepavucontrolInput tab, are there Port settings for both the built-in mic and the headset mic? Can you switch?
– dirkt
Mar 7 '17 at 7:06
Ok, got it for Pulseaudio. I can't find anything in pavucontrol in the Input tab. There's only "Built-in Audio Analog Stereo" and the "Monitor of Built-in Audio Analog Stereo" in the Input Devices, and I can choose the port "Internal Microphone (unplugged)", "Microphone (plugged in)" and "Dock Microphone (unplugged)", but either choice is the Jack Microphone.
– aRkadeFR
Mar 7 '17 at 21:08
The interesting point is "unplugged" for the internal mic. When you unplug the jack mic, does that change? Does the internal mic work at all? Intel HDA normally works out of the box, but if your laptop does something funny, you can inspect the codec nodes withcat /proc/asound/card*/codec#*(do both with jack mic unplugged and plugged, observer changes, too). This will need some amount of time to work through, though.
– dirkt
Mar 8 '17 at 7:21
When I unplugged the Jack microphone, the internal microphone works perfectly. And I have in the Input Devices pannel the three choices: "Internal Microphone", "Microphone (unplugged)", "Dock Microphone (unplugged)". So it's like there's a switch between "Internal Microphone" and "Microphone" depending I have the Jack microphone plugged in or not. I edit the question with the output ofcat /proc/asound/card*/codec#*. Thanks
– aRkadeFR
Mar 8 '17 at 9:25
As you run Pulseaudio, try to change Pulseaudio settings, not ALSA settings. In the
pavucontrol Input tab, are there Port settings for both the built-in mic and the headset mic? Can you switch?– dirkt
Mar 7 '17 at 7:06
As you run Pulseaudio, try to change Pulseaudio settings, not ALSA settings. In the
pavucontrol Input tab, are there Port settings for both the built-in mic and the headset mic? Can you switch?– dirkt
Mar 7 '17 at 7:06
Ok, got it for Pulseaudio. I can't find anything in pavucontrol in the Input tab. There's only "Built-in Audio Analog Stereo" and the "Monitor of Built-in Audio Analog Stereo" in the Input Devices, and I can choose the port "Internal Microphone (unplugged)", "Microphone (plugged in)" and "Dock Microphone (unplugged)", but either choice is the Jack Microphone.
– aRkadeFR
Mar 7 '17 at 21:08
Ok, got it for Pulseaudio. I can't find anything in pavucontrol in the Input tab. There's only "Built-in Audio Analog Stereo" and the "Monitor of Built-in Audio Analog Stereo" in the Input Devices, and I can choose the port "Internal Microphone (unplugged)", "Microphone (plugged in)" and "Dock Microphone (unplugged)", but either choice is the Jack Microphone.
– aRkadeFR
Mar 7 '17 at 21:08
The interesting point is "unplugged" for the internal mic. When you unplug the jack mic, does that change? Does the internal mic work at all? Intel HDA normally works out of the box, but if your laptop does something funny, you can inspect the codec nodes with
cat /proc/asound/card*/codec#* (do both with jack mic unplugged and plugged, observer changes, too). This will need some amount of time to work through, though.– dirkt
Mar 8 '17 at 7:21
The interesting point is "unplugged" for the internal mic. When you unplug the jack mic, does that change? Does the internal mic work at all? Intel HDA normally works out of the box, but if your laptop does something funny, you can inspect the codec nodes with
cat /proc/asound/card*/codec#* (do both with jack mic unplugged and plugged, observer changes, too). This will need some amount of time to work through, though.– dirkt
Mar 8 '17 at 7:21
When I unplugged the Jack microphone, the internal microphone works perfectly. And I have in the Input Devices pannel the three choices: "Internal Microphone", "Microphone (unplugged)", "Dock Microphone (unplugged)". So it's like there's a switch between "Internal Microphone" and "Microphone" depending I have the Jack microphone plugged in or not. I edit the question with the output of
cat /proc/asound/card*/codec#*. Thanks– aRkadeFR
Mar 8 '17 at 9:25
When I unplugged the Jack microphone, the internal microphone works perfectly. And I have in the Input Devices pannel the three choices: "Internal Microphone", "Microphone (unplugged)", "Dock Microphone (unplugged)". So it's like there's a switch between "Internal Microphone" and "Microphone" depending I have the Jack microphone plugged in or not. I edit the question with the output of
cat /proc/asound/card*/codec#*. Thanks– aRkadeFR
Mar 8 '17 at 9:25
add a comment |
1 Answer
1
active
oldest
votes
Partial answer: I'll explain some background, you still need to find out what goes wrong.
Intel HDA codecs are described as a graph of nodes, identified by hexadecimal values. You can use codecgraph to generate a graph as postscript file (though large graphs tend to be unreadable), but here's a crude textual representation:
N = Node P = Pin M = Mixer I = Audio In O = Audio Out S = Selector
I07 <- S24 <- P12* P13
I08 <- S23 <- P18* P19 P1a P1b P1d M0b
I09 <- S22 <- P18 P19 P1a P1b P1d M0b P12* P13 # capture stream = 1
O02 stream=1 # Speaker Playback Volume
O03 stream=1 # Headphone Playback Volume
O06 # Digital
M0b <- P18 P19 P1a P1b P1d
M0c <- O02 M0b # (Speaker)
M0d <- O03 M0b # (Headphone)
P12 # Fixd Mic Int / Internal Mic Boost Volume
P13 # N/A Lin Out Ext / Amp In # = Line In?
P14 <- M0c # Fixd Speaker Int / Speaker Playback
P15 <- M0c M0d* # Jack HP Out Ext Left / Headphone Playback
P16 <- M0c M0d* # N/A Speaker Ext Rear / Headphone Playback
P18 <- M0c* M0d # N/A Speaker Ext Rear / Amp I/O
P19 # N/A Speaker Ext Rear / Dock Mic Boost Volume
P1a # Jack Mic Ext Left / Mic Boost Volume
P1b <- M0c* M0d # N/A Speaker Ext Rear / Amp I/O
P1d # N/A Modem Ext
P1e <- N06 # N/A Speaker Ext Rear / Digital
I prefixed the nodes with their functions. Not all pins on the codec chip are connected to something, so just ignore those.
Just looking at recording, only node 09 is used for sound capture. Node 12 is the internal mic A/D converter, and node 1a is the external microphone jack A/D converter. In your dump, selector node 22 selects node 12 for capture, so I assume the dump was made without the headphone plugged in.
Now we need to find out what changes when you plug the headset in. Please save both codec#0 and the output of amixer -c0 contents in two temporary files, plug the headset in, and again save both in two different temporary files. Compare the files with diff -u8 etc, identify the nodes and controls that change, and update your question.
My guess is that the selector node 22 will switch to 1a, and there are possibly some mute and/or volume changes. However, I don't see an ALSA control at node 22, so I don't know how to influence it via amixer.
Also, look for Auto-Mute Mode or anything similar in amixer -c0 controls. If you find anything, disable it (try all combinations if there are several), and do the whole thing again. This way we can find out what the default ALSA automute code tries to do when plugging the headphone, and find out if possibly something else influences the hardware.
Edit: If I read the ALSA source correctly, it's not the ALSA driver switching Node 0x22. So the next guess is that it's maybe some System Management Mode (SMM) feature in your laptop, but that's a wild guess. (You could try to disable SMM on boot to test if that's the case, out of curiosity, but then likely other features of your Laptop will also stop working).
Anyway, in my opinion there should be an ALSA mixer control at this node, so the user change the setting. Please upgrade your kernel to the newest version you can, and see if anything changes. If not, file a bug with the ALSA developers, maybe they can add a "quirk" (special case) to the driver for your laptop. Include the codec dump, and identify your Laptop as precisely as possible. An lspci -nm or similar may also help, if they need the subsystem id of the sound device.
In the meantime, you can use hda-verb to directly switch Node 0x22. In Debian, it's part of the package alsa-utils. As root,
hda-verb /dev/snd/hwC0D0 0x22 GET_CONNECT_SEL 0
should show you the selected connection index (0-based) of Node 0x22. It should be either 2 or 6. If that works, with
hda-verb /dev/snd/hwC0D0 0x22 SET_CONNECT_SEL 2
you can switch the node to index 2 (or to 6 with 6 as the last argument). Verify with contents of codec#0 that it worked as intended. That should allow you to use the internal microphone after plugging in the headphone.
answered Mar 8 '17 at 17:30
dirktdirkt
16.7k21336
Thanks for the comment. I updated the question. I confirm your guess on the switch of the Node 22. Even without theAuto-Mute ModeI still see the switch after on theNode 22.
– aRkadeFR
Mar 10 '17 at 12:45
add a comment |
Your Answer
StackExchange.ready(function() {
var channelOptions = {
tags: "".split(" "),
id: "106"
};
initTagRenderer("".split(" "), "".split(" "), channelOptions);
StackExchange.using("externalEditor", function() {
// Have to fire editor after snippets, if snippets enabled
if (StackExchange.settings.snippets.snippetsEnabled) {
StackExchange.using("snippets", function() {
createEditor();
});
}
else {
createEditor();
}
});
function createEditor() {
StackExchange.prepareEditor({
heartbeatType: 'answer',
autoActivateHeartbeat: false,
convertImagesToLinks: false,
noModals: true,
showLowRepImageUploadWarning: true,
reputationToPostImages: null,
bindNavPrevention: true,
postfix: "",
imageUploader: {
brandingHtml: "Powered by u003ca class="icon-imgur-white" href="https://imgur.com/"u003eu003c/au003e",
contentPolicyHtml: "User contributions licensed under u003ca href="https://creativecommons.org/licenses/by-sa/3.0/"u003ecc by-sa 3.0 with attribution requiredu003c/au003e u003ca href="https://stackoverflow.com/legal/content-policy"u003e(content policy)u003c/au003e",
allowUrls: true
},
onDemand: true,
discardSelector: ".discard-answer"
,immediatelyShowMarkdownHelp:true
});
}
});
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function () {
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2funix.stackexchange.com%2fquestions%2f349613%2falsamixer-pulseaudio-choose-internal-mic-over-mic-jack%23new-answer', 'question_page');
}
);
Post as a guest
Required, but never shown
1 Answer
1
active
oldest
votes
1 Answer
1
active
oldest
votes
active
oldest
votes
active
oldest
votes
Partial answer: I'll explain some background, you still need to find out what goes wrong.
Intel HDA codecs are described as a graph of nodes, identified by hexadecimal values. You can use codecgraph to generate a graph as postscript file (though large graphs tend to be unreadable), but here's a crude textual representation:
N = Node P = Pin M = Mixer I = Audio In O = Audio Out S = Selector
I07 <- S24 <- P12* P13
I08 <- S23 <- P18* P19 P1a P1b P1d M0b
I09 <- S22 <- P18 P19 P1a P1b P1d M0b P12* P13 # capture stream = 1
O02 stream=1 # Speaker Playback Volume
O03 stream=1 # Headphone Playback Volume
O06 # Digital
M0b <- P18 P19 P1a P1b P1d
M0c <- O02 M0b # (Speaker)
M0d <- O03 M0b # (Headphone)
P12 # Fixd Mic Int / Internal Mic Boost Volume
P13 # N/A Lin Out Ext / Amp In # = Line In?
P14 <- M0c # Fixd Speaker Int / Speaker Playback
P15 <- M0c M0d* # Jack HP Out Ext Left / Headphone Playback
P16 <- M0c M0d* # N/A Speaker Ext Rear / Headphone Playback
P18 <- M0c* M0d # N/A Speaker Ext Rear / Amp I/O
P19 # N/A Speaker Ext Rear / Dock Mic Boost Volume
P1a # Jack Mic Ext Left / Mic Boost Volume
P1b <- M0c* M0d # N/A Speaker Ext Rear / Amp I/O
P1d # N/A Modem Ext
P1e <- N06 # N/A Speaker Ext Rear / Digital
I prefixed the nodes with their functions. Not all pins on the codec chip are connected to something, so just ignore those.
Just looking at recording, only node 09 is used for sound capture. Node 12 is the internal mic A/D converter, and node 1a is the external microphone jack A/D converter. In your dump, selector node 22 selects node 12 for capture, so I assume the dump was made without the headphone plugged in.
Now we need to find out what changes when you plug the headset in. Please save both codec#0 and the output of amixer -c0 contents in two temporary files, plug the headset in, and again save both in two different temporary files. Compare the files with diff -u8 etc, identify the nodes and controls that change, and update your question.
My guess is that the selector node 22 will switch to 1a, and there are possibly some mute and/or volume changes. However, I don't see an ALSA control at node 22, so I don't know how to influence it via amixer.
Also, look for Auto-Mute Mode or anything similar in amixer -c0 controls. If you find anything, disable it (try all combinations if there are several), and do the whole thing again. This way we can find out what the default ALSA automute code tries to do when plugging the headphone, and find out if possibly something else influences the hardware.
Edit: If I read the ALSA source correctly, it's not the ALSA driver switching Node 0x22. So the next guess is that it's maybe some System Management Mode (SMM) feature in your laptop, but that's a wild guess. (You could try to disable SMM on boot to test if that's the case, out of curiosity, but then likely other features of your Laptop will also stop working).
Anyway, in my opinion there should be an ALSA mixer control at this node, so the user change the setting. Please upgrade your kernel to the newest version you can, and see if anything changes. If not, file a bug with the ALSA developers, maybe they can add a "quirk" (special case) to the driver for your laptop. Include the codec dump, and identify your Laptop as precisely as possible. An lspci -nm or similar may also help, if they need the subsystem id of the sound device.
In the meantime, you can use hda-verb to directly switch Node 0x22. In Debian, it's part of the package alsa-utils. As root,
hda-verb /dev/snd/hwC0D0 0x22 GET_CONNECT_SEL 0
should show you the selected connection index (0-based) of Node 0x22. It should be either 2 or 6. If that works, with
hda-verb /dev/snd/hwC0D0 0x22 SET_CONNECT_SEL 2
you can switch the node to index 2 (or to 6 with 6 as the last argument). Verify with contents of codec#0 that it worked as intended. That should allow you to use the internal microphone after plugging in the headphone.
answered Mar 8 '17 at 17:30
dirktdirkt
16.7k21336
Thanks for the comment. I updated the question. I confirm your guess on the switch of the Node 22. Even without theAuto-Mute ModeI still see the switch after on theNode 22.
– aRkadeFR
Mar 10 '17 at 12:45
add a comment |
Partial answer: I'll explain some background, you still need to find out what goes wrong.
Intel HDA codecs are described as a graph of nodes, identified by hexadecimal values. You can use codecgraph to generate a graph as postscript file (though large graphs tend to be unreadable), but here's a crude textual representation:
N = Node P = Pin M = Mixer I = Audio In O = Audio Out S = Selector
I07 <- S24 <- P12* P13
I08 <- S23 <- P18* P19 P1a P1b P1d M0b
I09 <- S22 <- P18 P19 P1a P1b P1d M0b P12* P13 # capture stream = 1
O02 stream=1 # Speaker Playback Volume
O03 stream=1 # Headphone Playback Volume
O06 # Digital
M0b <- P18 P19 P1a P1b P1d
M0c <- O02 M0b # (Speaker)
M0d <- O03 M0b # (Headphone)
P12 # Fixd Mic Int / Internal Mic Boost Volume
P13 # N/A Lin Out Ext / Amp In # = Line In?
P14 <- M0c # Fixd Speaker Int / Speaker Playback
P15 <- M0c M0d* # Jack HP Out Ext Left / Headphone Playback
P16 <- M0c M0d* # N/A Speaker Ext Rear / Headphone Playback
P18 <- M0c* M0d # N/A Speaker Ext Rear / Amp I/O
P19 # N/A Speaker Ext Rear / Dock Mic Boost Volume
P1a # Jack Mic Ext Left / Mic Boost Volume
P1b <- M0c* M0d # N/A Speaker Ext Rear / Amp I/O
P1d # N/A Modem Ext
P1e <- N06 # N/A Speaker Ext Rear / Digital
I prefixed the nodes with their functions. Not all pins on the codec chip are connected to something, so just ignore those.
Just looking at recording, only node 09 is used for sound capture. Node 12 is the internal mic A/D converter, and node 1a is the external microphone jack A/D converter. In your dump, selector node 22 selects node 12 for capture, so I assume the dump was made without the headphone plugged in.
Now we need to find out what changes when you plug the headset in. Please save both codec#0 and the output of amixer -c0 contents in two temporary files, plug the headset in, and again save both in two different temporary files. Compare the files with diff -u8 etc, identify the nodes and controls that change, and update your question.
My guess is that the selector node 22 will switch to 1a, and there are possibly some mute and/or volume changes. However, I don't see an ALSA control at node 22, so I don't know how to influence it via amixer.
Also, look for Auto-Mute Mode or anything similar in amixer -c0 controls. If you find anything, disable it (try all combinations if there are several), and do the whole thing again. This way we can find out what the default ALSA automute code tries to do when plugging the headphone, and find out if possibly something else influences the hardware.
Edit: If I read the ALSA source correctly, it's not the ALSA driver switching Node 0x22. So the next guess is that it's maybe some System Management Mode (SMM) feature in your laptop, but that's a wild guess. (You could try to disable SMM on boot to test if that's the case, out of curiosity, but then likely other features of your Laptop will also stop working).
Anyway, in my opinion there should be an ALSA mixer control at this node, so the user change the setting. Please upgrade your kernel to the newest version you can, and see if anything changes. If not, file a bug with the ALSA developers, maybe they can add a "quirk" (special case) to the driver for your laptop. Include the codec dump, and identify your Laptop as precisely as possible. An lspci -nm or similar may also help, if they need the subsystem id of the sound device.
In the meantime, you can use hda-verb to directly switch Node 0x22. In Debian, it's part of the package alsa-utils. As root,
hda-verb /dev/snd/hwC0D0 0x22 GET_CONNECT_SEL 0
should show you the selected connection index (0-based) of Node 0x22. It should be either 2 or 6. If that works, with
hda-verb /dev/snd/hwC0D0 0x22 SET_CONNECT_SEL 2
you can switch the node to index 2 (or to 6 with 6 as the last argument). Verify with contents of codec#0 that it worked as intended. That should allow you to use the internal microphone after plugging in the headphone.
answered Mar 8 '17 at 17:30
dirktdirkt
16.7k21336
Thanks for the comment. I updated the question. I confirm your guess on the switch of the Node 22. Even without theAuto-Mute ModeI still see the switch after on theNode 22.
– aRkadeFR
Mar 10 '17 at 12:45
add a comment |
Partial answer: I'll explain some background, you still need to find out what goes wrong.
Intel HDA codecs are described as a graph of nodes, identified by hexadecimal values. You can use codecgraph to generate a graph as postscript file (though large graphs tend to be unreadable), but here's a crude textual representation:
N = Node P = Pin M = Mixer I = Audio In O = Audio Out S = Selector
I07 <- S24 <- P12* P13
I08 <- S23 <- P18* P19 P1a P1b P1d M0b
I09 <- S22 <- P18 P19 P1a P1b P1d M0b P12* P13 # capture stream = 1
O02 stream=1 # Speaker Playback Volume
O03 stream=1 # Headphone Playback Volume
O06 # Digital
M0b <- P18 P19 P1a P1b P1d
M0c <- O02 M0b # (Speaker)
M0d <- O03 M0b # (Headphone)
P12 # Fixd Mic Int / Internal Mic Boost Volume
P13 # N/A Lin Out Ext / Amp In # = Line In?
P14 <- M0c # Fixd Speaker Int / Speaker Playback
P15 <- M0c M0d* # Jack HP Out Ext Left / Headphone Playback
P16 <- M0c M0d* # N/A Speaker Ext Rear / Headphone Playback
P18 <- M0c* M0d # N/A Speaker Ext Rear / Amp I/O
P19 # N/A Speaker Ext Rear / Dock Mic Boost Volume
P1a # Jack Mic Ext Left / Mic Boost Volume
P1b <- M0c* M0d # N/A Speaker Ext Rear / Amp I/O
P1d # N/A Modem Ext
P1e <- N06 # N/A Speaker Ext Rear / Digital
I prefixed the nodes with their functions. Not all pins on the codec chip are connected to something, so just ignore those.
Just looking at recording, only node 09 is used for sound capture. Node 12 is the internal mic A/D converter, and node 1a is the external microphone jack A/D converter. In your dump, selector node 22 selects node 12 for capture, so I assume the dump was made without the headphone plugged in.
Now we need to find out what changes when you plug the headset in. Please save both codec#0 and the output of amixer -c0 contents in two temporary files, plug the headset in, and again save both in two different temporary files. Compare the files with diff -u8 etc, identify the nodes and controls that change, and update your question.
My guess is that the selector node 22 will switch to 1a, and there are possibly some mute and/or volume changes. However, I don't see an ALSA control at node 22, so I don't know how to influence it via amixer.
Also, look for Auto-Mute Mode or anything similar in amixer -c0 controls. If you find anything, disable it (try all combinations if there are several), and do the whole thing again. This way we can find out what the default ALSA automute code tries to do when plugging the headphone, and find out if possibly something else influences the hardware.
Edit: If I read the ALSA source correctly, it's not the ALSA driver switching Node 0x22. So the next guess is that it's maybe some System Management Mode (SMM) feature in your laptop, but that's a wild guess. (You could try to disable SMM on boot to test if that's the case, out of curiosity, but then likely other features of your Laptop will also stop working).
Anyway, in my opinion there should be an ALSA mixer control at this node, so the user change the setting. Please upgrade your kernel to the newest version you can, and see if anything changes. If not, file a bug with the ALSA developers, maybe they can add a "quirk" (special case) to the driver for your laptop. Include the codec dump, and identify your Laptop as precisely as possible. An lspci -nm or similar may also help, if they need the subsystem id of the sound device.
In the meantime, you can use hda-verb to directly switch Node 0x22. In Debian, it's part of the package alsa-utils. As root,
hda-verb /dev/snd/hwC0D0 0x22 GET_CONNECT_SEL 0
should show you the selected connection index (0-based) of Node 0x22. It should be either 2 or 6. If that works, with
hda-verb /dev/snd/hwC0D0 0x22 SET_CONNECT_SEL 2
you can switch the node to index 2 (or to 6 with 6 as the last argument). Verify with contents of codec#0 that it worked as intended. That should allow you to use the internal microphone after plugging in the headphone.
answered Mar 8 '17 at 17:30
dirktdirkt
16.7k21336
Partial answer: I'll explain some background, you still need to find out what goes wrong.
Intel HDA codecs are described as a graph of nodes, identified by hexadecimal values. You can use codecgraph to generate a graph as postscript file (though large graphs tend to be unreadable), but here's a crude textual representation:
N = Node P = Pin M = Mixer I = Audio In O = Audio Out S = Selector
I07 <- S24 <- P12* P13
I08 <- S23 <- P18* P19 P1a P1b P1d M0b
I09 <- S22 <- P18 P19 P1a P1b P1d M0b P12* P13 # capture stream = 1
O02 stream=1 # Speaker Playback Volume
O03 stream=1 # Headphone Playback Volume
O06 # Digital
M0b <- P18 P19 P1a P1b P1d
M0c <- O02 M0b # (Speaker)
M0d <- O03 M0b # (Headphone)
P12 # Fixd Mic Int / Internal Mic Boost Volume
P13 # N/A Lin Out Ext / Amp In # = Line In?
P14 <- M0c # Fixd Speaker Int / Speaker Playback
P15 <- M0c M0d* # Jack HP Out Ext Left / Headphone Playback
P16 <- M0c M0d* # N/A Speaker Ext Rear / Headphone Playback
P18 <- M0c* M0d # N/A Speaker Ext Rear / Amp I/O
P19 # N/A Speaker Ext Rear / Dock Mic Boost Volume
P1a # Jack Mic Ext Left / Mic Boost Volume
P1b <- M0c* M0d # N/A Speaker Ext Rear / Amp I/O
P1d # N/A Modem Ext
P1e <- N06 # N/A Speaker Ext Rear / Digital
I prefixed the nodes with their functions. Not all pins on the codec chip are connected to something, so just ignore those.
Just looking at recording, only node 09 is used for sound capture. Node 12 is the internal mic A/D converter, and node 1a is the external microphone jack A/D converter. In your dump, selector node 22 selects node 12 for capture, so I assume the dump was made without the headphone plugged in.
Now we need to find out what changes when you plug the headset in. Please save both codec#0 and the output of amixer -c0 contents in two temporary files, plug the headset in, and again save both in two different temporary files. Compare the files with diff -u8 etc, identify the nodes and controls that change, and update your question.
My guess is that the selector node 22 will switch to 1a, and there are possibly some mute and/or volume changes. However, I don't see an ALSA control at node 22, so I don't know how to influence it via amixer.
Also, look for Auto-Mute Mode or anything similar in amixer -c0 controls. If you find anything, disable it (try all combinations if there are several), and do the whole thing again. This way we can find out what the default ALSA automute code tries to do when plugging the headphone, and find out if possibly something else influences the hardware.
Edit: If I read the ALSA source correctly, it's not the ALSA driver switching Node 0x22. So the next guess is that it's maybe some System Management Mode (SMM) feature in your laptop, but that's a wild guess. (You could try to disable SMM on boot to test if that's the case, out of curiosity, but then likely other features of your Laptop will also stop working).
Anyway, in my opinion there should be an ALSA mixer control at this node, so the user change the setting. Please upgrade your kernel to the newest version you can, and see if anything changes. If not, file a bug with the ALSA developers, maybe they can add a "quirk" (special case) to the driver for your laptop. Include the codec dump, and identify your Laptop as precisely as possible. An lspci -nm or similar may also help, if they need the subsystem id of the sound device.
In the meantime, you can use hda-verb to directly switch Node 0x22. In Debian, it's part of the package alsa-utils. As root,
hda-verb /dev/snd/hwC0D0 0x22 GET_CONNECT_SEL 0
should show you the selected connection index (0-based) of Node 0x22. It should be either 2 or 6. If that works, with
hda-verb /dev/snd/hwC0D0 0x22 SET_CONNECT_SEL 2
you can switch the node to index 2 (or to 6 with 6 as the last argument). Verify with contents of codec#0 that it worked as intended. That should allow you to use the internal microphone after plugging in the headphone.
answered Mar 8 '17 at 17:30
dirktdirkt
16.7k21336
edited Mar 11 '17 at 16:14
answered Mar 8 '17 at 17:30
dirktdirkt
16.7k21336
answered Mar 8 '17 at 17:30
dirktdirkt
16.7k21336
answered Mar 8 '17 at 17:30
dirktdirkt
16.7k21336
16.7k21336
Thanks for the comment. I updated the question. I confirm your guess on the switch of the Node 22. Even without theAuto-Mute ModeI still see the switch after on theNode 22.
– aRkadeFR
Mar 10 '17 at 12:45
add a comment |
Thanks for the comment. I updated the question. I confirm your guess on the switch of the Node 22. Even without theAuto-Mute ModeI still see the switch after on theNode 22.
– aRkadeFR
Mar 10 '17 at 12:45
Thanks for the comment. I updated the question. I confirm your guess on the switch of the Node 22. Even without the
Auto-Mute Mode I still see the switch after on the Node 22.– aRkadeFR
Mar 10 '17 at 12:45
Thanks for the comment. I updated the question. I confirm your guess on the switch of the Node 22. Even without the
Auto-Mute Mode I still see the switch after on the Node 22.– aRkadeFR
Mar 10 '17 at 12:45
add a comment |
Thanks for contributing an answer to Unix & Linux Stack Exchange!
- Please be sure to answer the question. Provide details and share your research!
But avoid …
- Asking for help, clarification, or responding to other answers.
- Making statements based on opinion; back them up with references or personal experience.
To learn more, see our tips on writing great answers.
Some of your past answers have not been well-received, and you're in danger of being blocked from answering.
Please pay close attention to the following guidance:
- Please be sure to answer the question. Provide details and share your research!
But avoid …
- Asking for help, clarification, or responding to other answers.
- Making statements based on opinion; back them up with references or personal experience.
To learn more, see our tips on writing great answers.
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function () {
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2funix.stackexchange.com%2fquestions%2f349613%2falsamixer-pulseaudio-choose-internal-mic-over-mic-jack%23new-answer', 'question_page');
}
);
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
As you run Pulseaudio, try to change Pulseaudio settings, not ALSA settings. In the
pavucontrolInput tab, are there Port settings for both the built-in mic and the headset mic? Can you switch?– dirkt
Mar 7 '17 at 7:06
Ok, got it for Pulseaudio. I can't find anything in pavucontrol in the Input tab. There's only "Built-in Audio Analog Stereo" and the "Monitor of Built-in Audio Analog Stereo" in the Input Devices, and I can choose the port "Internal Microphone (unplugged)", "Microphone (plugged in)" and "Dock Microphone (unplugged)", but either choice is the Jack Microphone.
– aRkadeFR
Mar 7 '17 at 21:08
The interesting point is "unplugged" for the internal mic. When you unplug the jack mic, does that change? Does the internal mic work at all? Intel HDA normally works out of the box, but if your laptop does something funny, you can inspect the codec nodes with
cat /proc/asound/card*/codec#*(do both with jack mic unplugged and plugged, observer changes, too). This will need some amount of time to work through, though.– dirkt
Mar 8 '17 at 7:21
When I unplugged the Jack microphone, the internal microphone works perfectly. And I have in the Input Devices pannel the three choices: "Internal Microphone", "Microphone (unplugged)", "Dock Microphone (unplugged)". So it's like there's a switch between "Internal Microphone" and "Microphone" depending I have the Jack microphone plugged in or not. I edit the question with the output of
cat /proc/asound/card*/codec#*. Thanks– aRkadeFR
Mar 8 '17 at 9:25