Do SOIC op-amps packages behave differently from DIP?
I have acquired some mcp-6002 op-amps in a SOIC package instead of the DIP I normally use. I have solder these to a SOIC to DIP "converter" so to fit on the breadboard. If I connect them as I do with the DIP (as simple buffers for testing) they don't seem to work, I tested 4 of these and all of them behave similarly, the upper part of the wave is non-existent and I get a small part from the bottom of the signal. Now I tried to put a voltage divider with half-the supply (because they are single supply) feeding the inverting input and the wave appears but the upper part of the signal is kind of low-pass filtered. So the question is, have I damaged these during soldering to the convertors or they behave differently?
correction: "applied"
dip soic
asked 15 hours ago
John AmJohn Am
325214
|
show 5 more comments
I have acquired some mcp-6002 op-amps in a SOIC package instead of the DIP I normally use. I have solder these to a SOIC to DIP "converter" so to fit on the breadboard. If I connect them as I do with the DIP (as simple buffers for testing) they don't seem to work, I tested 4 of these and all of them behave similarly, the upper part of the wave is non-existent and I get a small part from the bottom of the signal. Now I tried to put a voltage divider with half-the supply (because they are single supply) feeding the inverting input and the wave appears but the upper part of the signal is kind of low-pass filtered. So the question is, have I damaged these during soldering to the convertors or they behave differently?
correction: "applied"
dip soic
asked 15 hours ago
John AmJohn Am
325214
Have you tried rotating the adapter board? maybe you soldered the ic on the wrong way.
– Linkyyy
15 hours ago
@ Linkyyy Yes I tested the connections several times. They should be identical isn't this right?
– John Am
15 hours ago
1
If the part number is the same, then they should work the same, regardless of package (ignoring minor things like tiny differences in inductance and capacitance that shouldn't be a problem in what you are doing.) The pinout is often the same on DIP and SOIC, but not always. The datasheet for the MCP6002 says DIP and SOIC have the same pinout.
– JRE
15 hours ago
1
@ SamGibson ebay, china. Yes perhaps there is also the possibility to be bad IC's. It has never occured to me again, though.
– John Am
15 hours ago
2
@JohnAm - Agreed, that seems a likely conclusion. However if they are not the marked part number, then they could be almost anything else :-( Unless you de-encapsulate the die and hope to spot something on it (under the microscope) that leads you to a specific part number, then I don't know how you could get confident about what you really have :-( Even if you do find a part number on the die, those devices you have could be rejects of that part number, and so not meet the datasheet specifications. In short, as far as I can see, all bets are off :-(
– SamGibson
15 hours ago
|
show 5 more comments
I have acquired some mcp-6002 op-amps in a SOIC package instead of the DIP I normally use. I have solder these to a SOIC to DIP "converter" so to fit on the breadboard. If I connect them as I do with the DIP (as simple buffers for testing) they don't seem to work, I tested 4 of these and all of them behave similarly, the upper part of the wave is non-existent and I get a small part from the bottom of the signal. Now I tried to put a voltage divider with half-the supply (because they are single supply) feeding the inverting input and the wave appears but the upper part of the signal is kind of low-pass filtered. So the question is, have I damaged these during soldering to the convertors or they behave differently?
correction: "applied"
dip soic
asked 15 hours ago
John AmJohn Am
325214
I have acquired some mcp-6002 op-amps in a SOIC package instead of the DIP I normally use. I have solder these to a SOIC to DIP "converter" so to fit on the breadboard. If I connect them as I do with the DIP (as simple buffers for testing) they don't seem to work, I tested 4 of these and all of them behave similarly, the upper part of the wave is non-existent and I get a small part from the bottom of the signal. Now I tried to put a voltage divider with half-the supply (because they are single supply) feeding the inverting input and the wave appears but the upper part of the signal is kind of low-pass filtered. So the question is, have I damaged these during soldering to the convertors or they behave differently?
correction: "applied"
dip soic
dip soic
asked 15 hours ago
John AmJohn Am
325214
asked 15 hours ago
John AmJohn Am
325214
edited 15 hours ago
John Am
asked 15 hours ago
John AmJohn Am
325214
asked 15 hours ago
John AmJohn Am
325214
asked 15 hours ago
John AmJohn Am
325214
325214
Have you tried rotating the adapter board? maybe you soldered the ic on the wrong way.
– Linkyyy
15 hours ago
@ Linkyyy Yes I tested the connections several times. They should be identical isn't this right?
– John Am
15 hours ago
1
If the part number is the same, then they should work the same, regardless of package (ignoring minor things like tiny differences in inductance and capacitance that shouldn't be a problem in what you are doing.) The pinout is often the same on DIP and SOIC, but not always. The datasheet for the MCP6002 says DIP and SOIC have the same pinout.
– JRE
15 hours ago
1
@ SamGibson ebay, china. Yes perhaps there is also the possibility to be bad IC's. It has never occured to me again, though.
– John Am
15 hours ago
2
@JohnAm - Agreed, that seems a likely conclusion. However if they are not the marked part number, then they could be almost anything else :-( Unless you de-encapsulate the die and hope to spot something on it (under the microscope) that leads you to a specific part number, then I don't know how you could get confident about what you really have :-( Even if you do find a part number on the die, those devices you have could be rejects of that part number, and so not meet the datasheet specifications. In short, as far as I can see, all bets are off :-(
– SamGibson
15 hours ago
|
show 5 more comments
Have you tried rotating the adapter board? maybe you soldered the ic on the wrong way.
– Linkyyy
15 hours ago
@ Linkyyy Yes I tested the connections several times. They should be identical isn't this right?
– John Am
15 hours ago
1
If the part number is the same, then they should work the same, regardless of package (ignoring minor things like tiny differences in inductance and capacitance that shouldn't be a problem in what you are doing.) The pinout is often the same on DIP and SOIC, but not always. The datasheet for the MCP6002 says DIP and SOIC have the same pinout.
– JRE
15 hours ago
1
@ SamGibson ebay, china. Yes perhaps there is also the possibility to be bad IC's. It has never occured to me again, though.
– John Am
15 hours ago
2
@JohnAm - Agreed, that seems a likely conclusion. However if they are not the marked part number, then they could be almost anything else :-( Unless you de-encapsulate the die and hope to spot something on it (under the microscope) that leads you to a specific part number, then I don't know how you could get confident about what you really have :-( Even if you do find a part number on the die, those devices you have could be rejects of that part number, and so not meet the datasheet specifications. In short, as far as I can see, all bets are off :-(
– SamGibson
15 hours ago
Have you tried rotating the adapter board? maybe you soldered the ic on the wrong way.
– Linkyyy
15 hours ago
Have you tried rotating the adapter board? maybe you soldered the ic on the wrong way.
– Linkyyy
15 hours ago
@ Linkyyy Yes I tested the connections several times. They should be identical isn't this right?
– John Am
15 hours ago
@ Linkyyy Yes I tested the connections several times. They should be identical isn't this right?
– John Am
15 hours ago
1
1
If the part number is the same, then they should work the same, regardless of package (ignoring minor things like tiny differences in inductance and capacitance that shouldn't be a problem in what you are doing.) The pinout is often the same on DIP and SOIC, but not always. The datasheet for the MCP6002 says DIP and SOIC have the same pinout.
– JRE
15 hours ago
If the part number is the same, then they should work the same, regardless of package (ignoring minor things like tiny differences in inductance and capacitance that shouldn't be a problem in what you are doing.) The pinout is often the same on DIP and SOIC, but not always. The datasheet for the MCP6002 says DIP and SOIC have the same pinout.
– JRE
15 hours ago
1
1
@ SamGibson ebay, china. Yes perhaps there is also the possibility to be bad IC's. It has never occured to me again, though.
– John Am
15 hours ago
@ SamGibson ebay, china. Yes perhaps there is also the possibility to be bad IC's. It has never occured to me again, though.
– John Am
15 hours ago
2
2
@JohnAm - Agreed, that seems a likely conclusion. However if they are not the marked part number, then they could be almost anything else :-( Unless you de-encapsulate the die and hope to spot something on it (under the microscope) that leads you to a specific part number, then I don't know how you could get confident about what you really have :-( Even if you do find a part number on the die, those devices you have could be rejects of that part number, and so not meet the datasheet specifications. In short, as far as I can see, all bets are off :-(
– SamGibson
15 hours ago
@JohnAm - Agreed, that seems a likely conclusion. However if they are not the marked part number, then they could be almost anything else :-( Unless you de-encapsulate the die and hope to spot something on it (under the microscope) that leads you to a specific part number, then I don't know how you could get confident about what you really have :-( Even if you do find a part number on the die, those devices you have could be rejects of that part number, and so not meet the datasheet specifications. In short, as far as I can see, all bets are off :-(
– SamGibson
15 hours ago
|
show 5 more comments
1 Answer
1
active
oldest
votes
Unfortunately this won't be the first time of ICs marked X not behaving as component X should do, having come from Ebay / AliExpress etc.
Since you have some known-good DIP versions of this device, and (excluding gross soldering mistakes) the SOIC version of this device should behave the same, I would be concerned that you don't have genuine, working ICs of the marked part number. We had another example of this situation with EEPROMs sold through AliExpress, in a question a few days ago. Sorry...
answered 15 hours ago
SamGibsonSamGibson
10.9k41537
add a comment |
Your Answer
StackExchange.ifUsing("editor", function () {
return StackExchange.using("mathjaxEditing", function () {
StackExchange.MarkdownEditor.creationCallbacks.add(function (editor, postfix) {
StackExchange.mathjaxEditing.prepareWmdForMathJax(editor, postfix, [["\$", "\$"]]);
});
});
}, "mathjax-editing");
StackExchange.ifUsing("editor", function () {
return StackExchange.using("schematics", function () {
StackExchange.schematics.init();
});
}, "cicuitlab");
StackExchange.ready(function() {
var channelOptions = {
tags: "".split(" "),
id: "135"
};
initTagRenderer("".split(" "), "".split(" "), channelOptions);
StackExchange.using("externalEditor", function() {
// Have to fire editor after snippets, if snippets enabled
if (StackExchange.settings.snippets.snippetsEnabled) {
StackExchange.using("snippets", function() {
createEditor();
});
}
else {
createEditor();
}
});
function createEditor() {
StackExchange.prepareEditor({
heartbeatType: 'answer',
autoActivateHeartbeat: false,
convertImagesToLinks: false,
noModals: true,
showLowRepImageUploadWarning: true,
reputationToPostImages: null,
bindNavPrevention: true,
postfix: "",
imageUploader: {
brandingHtml: "Powered by u003ca class="icon-imgur-white" href="https://imgur.com/"u003eu003c/au003e",
contentPolicyHtml: "User contributions licensed under u003ca href="https://creativecommons.org/licenses/by-sa/3.0/"u003ecc by-sa 3.0 with attribution requiredu003c/au003e u003ca href="https://stackoverflow.com/legal/content-policy"u003e(content policy)u003c/au003e",
allowUrls: true
},
onDemand: true,
discardSelector: ".discard-answer"
,immediatelyShowMarkdownHelp:true
});
}
});
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function () {
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2felectronics.stackexchange.com%2fquestions%2f416400%2fdo-soic-op-amps-packages-behave-differently-from-dip%23new-answer', 'question_page');
}
);
Post as a guest
Required, but never shown
1 Answer
1
active
oldest
votes
1 Answer
1
active
oldest
votes
active
oldest
votes
active
oldest
votes
Unfortunately this won't be the first time of ICs marked X not behaving as component X should do, having come from Ebay / AliExpress etc.
Since you have some known-good DIP versions of this device, and (excluding gross soldering mistakes) the SOIC version of this device should behave the same, I would be concerned that you don't have genuine, working ICs of the marked part number. We had another example of this situation with EEPROMs sold through AliExpress, in a question a few days ago. Sorry...
answered 15 hours ago
SamGibsonSamGibson
10.9k41537
add a comment |
Unfortunately this won't be the first time of ICs marked X not behaving as component X should do, having come from Ebay / AliExpress etc.
Since you have some known-good DIP versions of this device, and (excluding gross soldering mistakes) the SOIC version of this device should behave the same, I would be concerned that you don't have genuine, working ICs of the marked part number. We had another example of this situation with EEPROMs sold through AliExpress, in a question a few days ago. Sorry...
answered 15 hours ago
SamGibsonSamGibson
10.9k41537
add a comment |
Unfortunately this won't be the first time of ICs marked X not behaving as component X should do, having come from Ebay / AliExpress etc.
Since you have some known-good DIP versions of this device, and (excluding gross soldering mistakes) the SOIC version of this device should behave the same, I would be concerned that you don't have genuine, working ICs of the marked part number. We had another example of this situation with EEPROMs sold through AliExpress, in a question a few days ago. Sorry...
answered 15 hours ago
SamGibsonSamGibson
10.9k41537
Unfortunately this won't be the first time of ICs marked X not behaving as component X should do, having come from Ebay / AliExpress etc.
Since you have some known-good DIP versions of this device, and (excluding gross soldering mistakes) the SOIC version of this device should behave the same, I would be concerned that you don't have genuine, working ICs of the marked part number. We had another example of this situation with EEPROMs sold through AliExpress, in a question a few days ago. Sorry...
answered 15 hours ago
SamGibsonSamGibson
10.9k41537
answered 15 hours ago
SamGibsonSamGibson
10.9k41537
answered 15 hours ago
SamGibsonSamGibson
10.9k41537
answered 15 hours ago
SamGibsonSamGibson
10.9k41537
10.9k41537
add a comment |
add a comment |
Thanks for contributing an answer to Electrical Engineering Stack Exchange!
- Please be sure to answer the question. Provide details and share your research!
But avoid …
- Asking for help, clarification, or responding to other answers.
- Making statements based on opinion; back them up with references or personal experience.
Use MathJax to format equations. MathJax reference.
To learn more, see our tips on writing great answers.
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
StackExchange.ready(
function () {
StackExchange.openid.initPostLogin('.new-post-login', 'https%3a%2f%2felectronics.stackexchange.com%2fquestions%2f416400%2fdo-soic-op-amps-packages-behave-differently-from-dip%23new-answer', 'question_page');
}
);
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Sign up or log in
StackExchange.ready(function () {
StackExchange.helpers.onClickDraftSave('#login-link');
});
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Sign up using Google
Sign up using Facebook
Sign up using Email and Password
Post as a guest
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Required, but never shown
Have you tried rotating the adapter board? maybe you soldered the ic on the wrong way.
– Linkyyy
15 hours ago
@ Linkyyy Yes I tested the connections several times. They should be identical isn't this right?
– John Am
15 hours ago
1
If the part number is the same, then they should work the same, regardless of package (ignoring minor things like tiny differences in inductance and capacitance that shouldn't be a problem in what you are doing.) The pinout is often the same on DIP and SOIC, but not always. The datasheet for the MCP6002 says DIP and SOIC have the same pinout.
– JRE
15 hours ago
1
@ SamGibson ebay, china. Yes perhaps there is also the possibility to be bad IC's. It has never occured to me again, though.
– John Am
15 hours ago
2
@JohnAm - Agreed, that seems a likely conclusion. However if they are not the marked part number, then they could be almost anything else :-( Unless you de-encapsulate the die and hope to spot something on it (under the microscope) that leads you to a specific part number, then I don't know how you could get confident about what you really have :-( Even if you do find a part number on the die, those devices you have could be rejects of that part number, and so not meet the datasheet specifications. In short, as far as I can see, all bets are off :-(
– SamGibson
15 hours ago